A. amplifier
B. attenuator
C. regenerator
D. light emitter
E. optical switch
F. optical receiver
G. fiber-optic cable
您可能感興趣的試卷
你可能感興趣的試題
A. OSNR
B. dispersion
C. attenuation
D. power budget
E. amplifier spacing
F. four wave mixing
A. PIN photodiodes
B. zero-chirped lasers
C. Erbium-doped fiber amplifiers
D. dispersion compensating fiber
E. dispersion compensating Bragg grating
A. They are both regions of lowest loss.
B. They are both regions of low reflections.
C. They are both regions of low index of refraction.
D. They are both regions of low chromatic dispersion.
E. They are both regions of low Polarization Mode Dispersion (PMD).
A. low optical powe
B. high optical power
C. few optical channels
D. many optical channels
E. low chromatic dispersion
F. high chromatic dispersion
G. too much power differential in the optical channels
Given the formula: (Fiber Attenuation * Km) + (Splice Attenuation * # of Splices) + (Connector Attenuation * # of Connectors) + (Optical Fiber or OADM) + Buffer(Fiber aging)) With regard to SONET/SDH optical calculations,
what will the given formula provide?()
A. fiber loss
B. OSNR level
C. post amplification
D. index of reflection
E. index of refraction
F. power post amplification budget
Click the Exhibit button.
Which type of multiplexer is shown in the exhibit?()
A. Thin Film filter
B. Fiber Bragg Grating
C. Arrayed Wave Guide
D. Erbium fiber amplifier
A. fiber dispersion
B. signal attenuation
C. transmitter power
D. amplifier bandwidth
E. receiver dispersion tolerance
A. 0 ps/nm
B. 340 ps/nm
C. 200 ps/nm
D. 3400 ps/nm
E. More information is needed.
A. The glass core is doped with an Erbium in periodic segments of the fiber.
B. Layers of high index ?and low index ?material are deposited on a glass substrate.
C. Thin layers of silica glass are placed onto wafers to produce a prism-like effect.
D. Fiber is etched with an ultraviolet laser that is precisely spaced for specific wavelength filtering.
Click the Exhibit button. When designing a DWDM system with multiple amplified spans, a pre-amp is needed at Site B to ().
A. offset the OADM loss at site B
B. overcome the high multiplexer loss at site A
C. amplify signal levels after the high loss through Fiber Span 1
D. adjust add channels at site B to be at the same level as the passthrough channels
E. ensure that the per channel power is higher than the minimum needed for the post-amp at Site B
最新試題
In SDH, what is the name of the embedded Data Communication Channel (DCC) in bytes D1-D3?()
Click the Exhibit button. What is the maximum allowable loss budget between the ONS 15216 Mux (left side) composite output and the ONS 15216 Demux (right side) composite input, with the optical values given in the exhibit? (Assume the worst case loss of 4.5 dB for 15216 200 GHz Mux/Demux and ignore power penalties or extra margin.) ()
Why are the 1300 nm and 1550 nm regions of the fiber spectrum primarily used for optical communications?()
What are three factors that limit the maximum distance of an amplified optical signal without regeneration? ()
Which three technologies are used to reduce chromatic dispersion accumulation in fiber-optic transmission systems?()
What protection method is used in 4F MS-SPRing networks?()
Click the Exhibit button. Which type of multiplexer is shown in the exhibit?()
What are two important considerations when using 2- or 4-channel 15216 OADMs?()
The ONS 15216 is a 32-channel system. The ONS 15216 OADMs are capable of adding and dropping one, two, or four channels. How are the OADMs provisioned to add and drop specific channels?()
Which timing mode is appropriate for an SDH NE that is adjacent to an SDH NE Bits-1 timing? ()