Click the Exhibit button. When designing a DWDM system with multiple amplified spans, a pre-amp is needed at Site B to ().
A. offset the OADM loss at site B
B. overcome the high multiplexer loss at site A
C. amplify signal levels after the high loss through Fiber Span 1
D. adjust add channels at site B to be at the same level as the passthrough channels
E. ensure that the per channel power is higher than the minimum needed for the post-amp at Site B
您可能感興趣的試卷
你可能感興趣的試題
In the OSNR model for EDFA amplifiers, SNR OUT = 1/(1/SNR IN + FhvB/P IN ),
what does SNR IN represent?()
A. the signal to noise of the current optical amplifier
B. the signal to noise of the previous amplifier or source
C. the signal to noise introduced by the optical multiplexer
D. the accumulated noise to signal ratio of the optical channel
The dispersion of a non-zero dispersion shifted fiber is 6 ps/nm*km at 1550 nm and 10 ps/nm*km at 1610 nm.
What is the minimum dispersion compensation required if an L-Band DWDM signal travels through 200 km of fiber and has a dispersion tolerance of 1800 ps/nm?()
A. none
B. -600 ps/nm
C. -200 ps/nm
D. +200 ps/nm
E. +600 ps/nm
A. 0.4 nanometers
B. 0.6 nanometers
C. 0.8 nanometers
D. 1.2 nanometers
E. 1.6 nanometers
Click the Exhibit button. Within an ONS 15454, you are provisioning a circuit on an unprotected SNCP ring. In the exhibit,
which two must you configure?()
A. revertive
B. circuit size
C. circuit type
D. bidirectional
E. protected drops
F. Switch on PDI-P
A. line timing
B. loop timing
C. internal timing
D. through timing
E. external timing
A. 512
B. 255
C. 1024
D. 4096
You are installing a Cisco ONS 15454 SDH in a service provider site. An E3 cable is being connected to a digital cross-connect system.
What is the maximum distance allowed between the two?()
A. 225 ft
B. 450 ft
C. 655 ft
D. 900 ft
A. An equal amount of working and protect bandwidth is required.
B. DCC bandwidth is not large enough to handle K1/K2 processing.
C. Switch times would exceed 50 ms for an STM-1 MS-SPRing ring.
D. There is not enough bandwidth in an STM-1 ring to justify MS-SPRing protection.
You are provisioning an E-1 circuit on an ONS 15454 SNCP configuration and XC-VXL-10G card.
How many total ports are used within the Low-Order matrix at the source node?()
A. 0
B. 1
C. 2
D. 3
E. 5
A. It protects signals against node failures between rings.
B. It protects signals against node failure within a single ring.
C. It allows for traffic to be preempted when a ring switch occurs.
D. Traffic can be dropped and continued at interconnecting nodes.
E. It protects preemptible traffic from being dropped when a ring switch occurs.
最新試題
In the OSNR model for EDFA amplifiers, SNR OUT = 1/(1/SNR IN + FhvB/P IN ), what does SNR IN represent?()
If the dispersion of a given fiber is 17ps/nm*km at 1550 nm and zero at 1310 nm, then what is the accumulated dispersion of an ITU wavelength after it travels 200 km? ()
Which two can be transported in one AU-4? ()
Which is a legitimate bandwidth matched pair?()
How is a Thin Film filter fabricated? ()
A VC-4-4c consists of ().
Which timing mode is appropriate for an SDH NE that is adjacent to an SDH NE Bits-1 timing? ()
SDH Code Violations (CVs) totals in the PM tables are actually an accumulation of the number of().
Click the Exhibit button. Within an ONS 15454, you are provisioning a circuit on an unprotected SNCP ring. In the exhibit, which two must you configure?()
Why are the 1300 nm and 1550 nm regions of the fiber spectrum primarily used for optical communications?()