A. line timing
B. loop timing
C. internal timing
D. through timing
E. external timing
您可能感興趣的試卷
你可能感興趣的試題
A. 512
B. 255
C. 1024
D. 4096
You are installing a Cisco ONS 15454 SDH in a service provider site. An E3 cable is being connected to a digital cross-connect system.
What is the maximum distance allowed between the two?()
A. 225 ft
B. 450 ft
C. 655 ft
D. 900 ft
A. An equal amount of working and protect bandwidth is required.
B. DCC bandwidth is not large enough to handle K1/K2 processing.
C. Switch times would exceed 50 ms for an STM-1 MS-SPRing ring.
D. There is not enough bandwidth in an STM-1 ring to justify MS-SPRing protection.
You are provisioning an E-1 circuit on an ONS 15454 SNCP configuration and XC-VXL-10G card.
How many total ports are used within the Low-Order matrix at the source node?()
A. 0
B. 1
C. 2
D. 3
E. 5
A. It protects signals against node failures between rings.
B. It protects signals against node failure within a single ring.
C. It allows for traffic to be preempted when a ring switch occurs.
D. Traffic can be dropped and continued at interconnecting nodes.
E. It protects preemptible traffic from being dropped when a ring switch occurs.
A customer would like to create a 1:1 protection group with a DS3Ni-12 card.
Where should it be placed in the chassis?()
A. only Slots 6 or 12
B. only Slots 3 or 15
C. high or low speed slots
D. directly adjacent to the working card
E. high-speed slots only (5/6 and 12/13)
A customer has 20 E1s to add between far-end nodes in an SNCP ring.
What type of circuit would you recommend?()
A. LO-PATH circuits
B. HO-PATH circuits
C. 1:1 protection circuits
D. 1:N protection circuits
E. LO-PATH tunnel circuits
Click the Exhibit button. As shown in the exhibit, a customer has several interconnected core rings. They want to create several irtual rings?utilizing their STM-64 backbone (nodes 1, 2, 3, and 4).
What do you recommend? ()
A. SNCP rings
B. MS-SPRing rings
C. 1:N protection on all core circuits
D. dual-ring interconnect with MS-SPRing rings
A customer has 2 E1s to add between far-end nodes in an SNCP ring.
What type of circuit should you recommend? ()
A. LO-PATH circuits
B. HO-PATH circuits
C. 1:1 protection circuits
D. 1:N protection circuits
E. LO-TUNNEL tunnel circuits
A. signal fail, signal degrade, manual switch
B. signal degrade, signal fail, manual switch
C. protection lockout, manual switch, path AIS
D. forced switch, manual switch, signal degrade
E. protection lockout, manual switch, forced switch
最新試題
What are two important considerations when using 2- or 4-channel 15216 OADMs?()
Which two can be transported in one AU-4? ()
What are three relevant design considerations when using the 15216 EDFA?()
In order to avoid misconnections due to a failed node in an MS-SPRing, Alarm Indication Signals (AISs) are sent on every channel normally terminating in that node. What is the name of this process?()
Click the Exhibit button. What is the maximum allowable loss budget between the ONS 15216 Mux (left side) composite output and the ONS 15216 Demux (right side) composite input, with the optical values given in the exhibit? (Assume the worst case loss of 4.5 dB for 15216 200 GHz Mux/Demux and ignore power penalties or extra margin.) ()
How is a Thin Film filter fabricated? ()
On an ONS 15454 node you can tunnel a(n) ().
In the OSNR model for EDFA amplifiers, SNR OUT = 1/(1/SNR IN + FhvB/P IN ), what does SNR IN represent?()
The dispersion of a non-zero dispersion shifted fiber is 6 ps/nm*km at 1550 nm and 10 ps/nm*km at 1610 nm. What is the minimum dispersion compensation required if an L-Band DWDM signal travels through 200 km of fiber and has a dispersion tolerance of 1800 ps/nm?()
Given the formula: (Fiber Attenuation * Km) + (Splice Attenuation * # of Splices) + (Connector Attenuation * # of Connectors) + (Optical Fiber or OADM) + Buffer(Fiber aging)) With regard to SONET/SDH optical calculations, what will the given formula provide?()