A. It protects signals against node failures between rings.
B. It protects signals against node failure within a single ring.
C. It allows for traffic to be preempted when a ring switch occurs.
D. Traffic can be dropped and continued at interconnecting nodes.
E. It protects preemptible traffic from being dropped when a ring switch occurs.
您可能感興趣的試卷
你可能感興趣的試題
A customer would like to create a 1:1 protection group with a DS3Ni-12 card.
Where should it be placed in the chassis?()
A. only Slots 6 or 12
B. only Slots 3 or 15
C. high or low speed slots
D. directly adjacent to the working card
E. high-speed slots only (5/6 and 12/13)
A customer has 20 E1s to add between far-end nodes in an SNCP ring.
What type of circuit would you recommend?()
A. LO-PATH circuits
B. HO-PATH circuits
C. 1:1 protection circuits
D. 1:N protection circuits
E. LO-PATH tunnel circuits
Click the Exhibit button. As shown in the exhibit, a customer has several interconnected core rings. They want to create several irtual rings?utilizing their STM-64 backbone (nodes 1, 2, 3, and 4).
What do you recommend? ()
A. SNCP rings
B. MS-SPRing rings
C. 1:N protection on all core circuits
D. dual-ring interconnect with MS-SPRing rings
A customer has 2 E1s to add between far-end nodes in an SNCP ring.
What type of circuit should you recommend? ()
A. LO-PATH circuits
B. HO-PATH circuits
C. 1:1 protection circuits
D. 1:N protection circuits
E. LO-TUNNEL tunnel circuits
A. signal fail, signal degrade, manual switch
B. signal degrade, signal fail, manual switch
C. protection lockout, manual switch, path AIS
D. forced switch, manual switch, signal degrade
E. protection lockout, manual switch, forced switch
A. LEX
B. HDLC
C. GFP-F
D. PPP/BCP
You are provisioning an E-1 circuit on an ONS 15454 MS-SPRing configuration and XC-VXL-10G card. Each VC-12 connection must also terminate via the VC-3 matrix.
How many VC-3 ports remain after this circuit is created, assuming no other circuits?()
A. 92
B. 93
C. 94
D. 95
E. 96
A. 1+1 is based on APS, while 1:1 is based on IPS.
B. 1:1 is used in SNCP switching, while 1+1 is used in MS-SPRing switching.
C. 1+1 sends signals on Working and Protect paths, while 1:1 sends signals only on Working path.
D. 1+1 sends signals on Working path ONLY, while 1:1 sends signals on both Working and Protect paths.
A. 10
B. 32
C. 64
D. 84
E. 96
A. line timing
B. loop timing
C. internal timing
D. through timing
E. external timing
最新試題
Which timing mode is appropriate for an SDH NE that is adjacent to an SDH NE Bits-1 timing? ()
Given the formula: (Fiber Attenuation * Km) + (Splice Attenuation * # of Splices) + (Connector Attenuation * # of Connectors) + (Optical Fiber or OADM) + Buffer(Fiber aging)) With regard to SONET/SDH optical calculations, what will the given formula provide?()
On an ONS 15454 node you can tunnel a(n) ().
Which three technologies are used to reduce chromatic dispersion accumulation in fiber-optic transmission systems?()
Click the Exhibit button. When designing a DWDM system with multiple amplified spans, a pre-amp is needed at Site B to ().
If the power is 0 dBm, what is the power in mW?()
How is a Thin Film filter fabricated? ()
What are three factors that limit the maximum distance of an amplified optical signal without regeneration? ()
A 2.5 Gb/s (OC-48 or STM-16) optical signal with a dispersion tolerance of 1200 ps/nm goes through fiber with 18ps/nm*km of dispersion. How many 15216-DCU-350 equivalents are needed for enough compensation after traveling 100 km?()
If the dispersion of a given fiber is 17ps/nm*km at 1550 nm and zero at 1310 nm, then what is the accumulated dispersion of an ITU wavelength after it travels 200 km? ()