A. All "Add" channels require uniform power levels.
B. The flexibility of wavelengths per OADM is limited.
C. It is easier to balance "Pass-Through" and "Add" channels.
D. There is lower pass-through loss using multi-channel OADMs.
E. You can extract a single channel without dropping other channels.
您可能感興趣的試卷
你可能感興趣的試題
Click the Exhibit button. What is the maximum allowable loss budget between the ONS 15216 Mux (left side) composite output and the ONS 15216 Demux (right side) composite input,
with the optical values given in the exhibit? (Assume the worst case loss of 4.5 dB for 15216 200 GHz Mux/Demux and ignore power penalties or extra margin.) ()
A. 15 dB
B. 17 dB
C. 21 dB
D. 26 dB
E. 27 dB
A 2.5 Gb/s (OC-48 or STM-16) optical signal with a dispersion tolerance of 1200 ps/nm goes through fiber with 18ps/nm*km of dispersion.
How many 15216-DCU-350 equivalents are needed for enough compensation after traveling 100 km?()
A. none
B. one
C. two
D. three
E. four
The ONS 15216 is a 32-channel system. The ONS 15216 OADMs are capable of adding and dropping one, two, or four channels.
How are the OADMs provisioned to add and drop specific channels?()
A. The ONS 15216 OADM can be provisioned to add/drop one, two, or four channels via Cisco Transport Manager (CTM).
B. The ONS 15216 OADM consists only of a four-channel module, and the number of ports utilized determines whether it is a one, two, or four channel OADM.
C. Three separate OADM modules are available for one, two, and four channels. The wavelengths to be dropped and added are programmable via Cisco Transport Manager (CTM).
D. The ONS 15216 OADM consists only of a single-channel module. Two-channel and four-channel support is available by stacking the single-channel module.
E. The ONS 15216 OADM is available in one, two, four channels. There are 32 single-channel OADM modules, 16 two-channel OADM modules, and 8 four-channel OADM modules.
A. dispersion
B. Optical SNR
C. span attenuation
D. four wave mixing
E. receiver sensitivity
A. 0 mW
B. 1 mW
C. 10 mW
D. 1.5 mW
A. lower cost
B. higher chirp
C. easier to manufacture
D. higher dispersion tolerance
E. higher optical signal-to-noise ratio
A. OSNR
B. dispersion
C. light skew
D. attenuation
A. amplifier
B. attenuator
C. regenerator
D. light emitter
E. optical switch
F. optical receiver
G. fiber-optic cable
A. OSNR
B. dispersion
C. attenuation
D. power budget
E. amplifier spacing
F. four wave mixing
A. PIN photodiodes
B. zero-chirped lasers
C. Erbium-doped fiber amplifiers
D. dispersion compensating fiber
E. dispersion compensating Bragg grating
最新試題
SDH Code Violations (CVs) totals in the PM tables are actually an accumulation of the number of().
Which three technologies are used to reduce chromatic dispersion accumulation in fiber-optic transmission systems?()
In SDH, what is the name of the embedded Data Communication Channel (DCC) in bytes D1-D3?()
On an ONS 15454 node you can tunnel a(n) ().
Click the Exhibit button. Within an ONS 15454, you are provisioning a circuit on an unprotected SNCP ring. In the exhibit, which two must you configure?()
Given the formula: (Fiber Attenuation * Km) + (Splice Attenuation * # of Splices) + (Connector Attenuation * # of Connectors) + (Optical Fiber or OADM) + Buffer(Fiber aging)) With regard to SONET/SDH optical calculations, what will the given formula provide?()
How is SNCP and MS-SPRing traffic rerouted during a protection switch when a complete fiber cable cut occurs?()
Click the Exhibit button. When designing a DWDM system with multiple amplified spans, a pre-amp is needed at Site B to ().
Click the Exhibit button. What is the maximum allowable loss budget between the ONS 15216 Mux (left side) composite output and the ONS 15216 Demux (right side) composite input, with the optical values given in the exhibit? (Assume the worst case loss of 4.5 dB for 15216 200 GHz Mux/Demux and ignore power penalties or extra margin.) ()
What three in combination are factors that can cause four-wave mixing in fiber-optic cables?()