A. Can be used to migrate from a 6120 to a 6140 and retain the same service profiles
B. Can only be used on the fabric interconnect on which it was created
C. Can be used to migrate from a 6120 to 6140 and retain system IP addresses and cluster information
D. Can be used to match firmware versions between 6120 and 6140 during a migration
您可能感興趣的試卷
你可能感興趣的試題
A. They are created automatically and stored on the FI
B. They are created manually and exported to a remote server
C. They are automatically scheduled to run every 24 hours
D. They are manually scheduled and stored on the FI
A. During the initial configuration from the console
B. Once the basic configuration has been applied
C. To restore the configuration on a secondary fabric interconnect
D. To upgrade the firmware on a replacement fabric interconnect
A. Only to Cisco Fibre Channel switches
B. Only to Cisco Fibre Channel switches in NPIV mode
C. To any Fibre Channel switch
D. Directly to storage arrays
E. Only to Nexus Switches
A. Under the Admin tab on the FI
B. Under the Server tab in the service profile
C. Under the SAN tab on each VSAN
D. Under the Admin tab on the chassis
E. Under the SAN tab on the Fabric Interconnect
Given the following output：
san-port-channel 12 is up
Hardware is Fibre Channel
Port WWN is 24：0c：00：0d：ec：d3：5c：00
Admin port mode is NP， trunk mode is on
Port mode is NP Port vsan is 1
Speed is 8 Gbps
Member[1] ： fc2/3
Member[2] ： fc2/4
What does "Speed is 8 Gbps" indicate？（）
A. The speed of the slowest interface in the port channel
B. The combined speed of all interfaces configured in the port channel
C. The combined speed of all interfaces in the port channel that are up
D. The speed that can be achieved if all buffers are used
A. Server
B. End device
C. Node
D. Host
E. Virtual
A. Sending all broadcasts
B. Receiving all traffic from upstream switches
C. Receiving broadcast traffic
D. Negotiating spanning tree with upstream switches
E. Learning MAC addresses from upstream switches
A. The Cisco VIC can create an unlimited number of Virtual NICs
B. The number of vNICs on the Cisco VIC that can be created is determined by the number of chassis uplinks
C. vNICs are created using software on the host operating system
D. The host operating system sees a vNIC as a physical PCIe device
E. The host operating system sees a vNIC as a sub-interface of a primary NIC
F. The Cisco VIC can create 1024 vNICs
A. Fibre Channel storage
B. UCS C-Series servers
C. NFS storage
D. UCS chassis
E. Other fabric interconnect
A. End-host mode is synonymous with NPV mode.
B. In end-host mode， only hard pinning of vHBAs to Fibre Channel uplink ports is allowed.
C. Making configuration changes between Fibre Channel switching mode and end-host mode is nondisruptive.
D. End-host mode is the default Fibre Channel switching mode.
最新試題
Refer to the exhibit.Your company requires a Cisco UCS configuration that will， at a minimum， allow the configuration in the provided exhibit. Which Cisco UCS components will meet the requirement？（）
Refer to the exhibit. According to the equipment tab in Cisco UCS Manager， which is true？（）
An administrator creates a vNIC and assigns it to Fabric A with the fabric failover feature enabled. Which statement is true？（）
What would be the cause for the following fault in UCS Manager？（） "ether VIF x / xxx down， reason： ENM source pinning failed"
Server load balancing （SLB） is the process of deciding to which server a load-balancing device should send a client request for service. Which predictors are supported on ACE in order to select the best server to fulfill a client request？ （）
In a Cisco Unified Computing System， What is the "designated receiver" port in end-host mode used for？（）
What is the use of an "all configuration" backup in Cisco UCS？（）
What is the purpose of this command in a Cisco Application Control Engine？（） switch/Admin# show np 1 me-stats "-F0 v"
Where are SAN Port Channel is created in UCS Manager？（）
Your company wants Server 1/eth0 （vNIC 1） configured so that it always uses Fabric Interconnect A Port Channel 1 （Po1） when it communicates with anything outside of the Cisco UCS domain. However， if vNIC 1 fails over to Fabric Interconnect B using fabric failover， then vNIC 1 can any uplink port on Fabric Interconnect B. Which statements are true？ （）