A. During the initial configuration from the console
B. Once the basic configuration has been applied
C. To restore the configuration on a secondary fabric interconnect
D. To upgrade the firmware on a replacement fabric interconnect
您可能感興趣的試卷
你可能感興趣的試題
A. Only to Cisco Fibre Channel switches
B. Only to Cisco Fibre Channel switches in NPIV mode
C. To any Fibre Channel switch
D. Directly to storage arrays
E. Only to Nexus Switches
A. Under the Admin tab on the FI
B. Under the Server tab in the service profile
C. Under the SAN tab on each VSAN
D. Under the Admin tab on the chassis
E. Under the SAN tab on the Fabric Interconnect
Given the following output:
san-port-channel 12 is up
Hardware is Fibre Channel
Port WWN is 24:0c:00:0d:ec:d3:5c:00
Admin port mode is NP, trunk mode is on
Port mode is NP Port vsan is 1
Speed is 8 Gbps
Member[1] : fc2/3
Member[2] : fc2/4
What does "Speed is 8 Gbps" indicate?()
A. The speed of the slowest interface in the port channel
B. The combined speed of all interfaces configured in the port channel
C. The combined speed of all interfaces in the port channel that are up
D. The speed that can be achieved if all buffers are used
A. Server
B. End device
C. Node
D. Host
E. Virtual
A. Sending all broadcasts
B. Receiving all traffic from upstream switches
C. Receiving broadcast traffic
D. Negotiating spanning tree with upstream switches
E. Learning MAC addresses from upstream switches
A. The Cisco VIC can create an unlimited number of Virtual NICs
B. The number of vNICs on the Cisco VIC that can be created is determined by the number of chassis uplinks
C. vNICs are created using software on the host operating system
D. The host operating system sees a vNIC as a physical PCIe device
E. The host operating system sees a vNIC as a sub-interface of a primary NIC
F. The Cisco VIC can create 1024 vNICs
A. Fibre Channel storage
B. UCS C-Series servers
C. NFS storage
D. UCS chassis
E. Other fabric interconnect
A. End-host mode is synonymous with NPV mode.
B. In end-host mode, only hard pinning of vHBAs to Fibre Channel uplink ports is allowed.
C. Making configuration changes between Fibre Channel switching mode and end-host mode is nondisruptive.
D. End-host mode is the default Fibre Channel switching mode.
A. In the blade BIOS
B. In the operating system
C. In the service profile
D. In the card option ROM
A. The QoS policy assigns a system class to the outgoing traffic for a vNIC or vHBA.
B. Flow-control policies determine whether the uplink Ethernet ports in a Cisco UCS environment send and receive IEEE 802.3x pause frames when the send buffer for a port fills.
C. If no system class is configured as CoS 0, the Fibre Channel system class is used.
D. The user can configure QoS for these system classes: platinum, gold, silver, best effort, Fibre Channel.
E. When configuring a system class, the type of adapter in a server may limit the maximum MTU supported.
最新試題
Where are SAN Port Channel is created in UCS Manager?()
What interface is created when an FC Port Channel is created on a Cisco Unified Computing System?()
Your company wants Server 1/eth0 (vNIC 1) configured so that it always uses Fabric Interconnect A Port Channel 1 (Po1) when it communicates with anything outside of the Cisco UCS domain. However, if vNIC 1 fails over to Fabric Interconnect B using fabric failover, then vNIC 1 can any uplink port on Fabric Interconnect B. Which statements are true? ()
When testing ICMP access to a functional load-balancing ACE VIP, it fails. What is the reason of this problem? ()
What is the purpose of this command in a Cisco Application Control Engine?() switch/Admin# show np 1 me-stats "-F0 v"
Which three statements are possible causes for the "fltAdaptorHostIfLink-down" fault in UCS Manager? ()
From the Cisco UCS CLI, how do you verify which uplink ports a blade server is using for its network connectivity?()
Refer to the exhibit.The Cisco UCS domain is operating in switching mode. A network administrator notices that no traffic is traversing the uplinks on Fabric Interconnect B (Path C). Which actions might be used to change this behavior?()
Which GSS "source access list" is used to allow access to GSS by clients when GSS is being used as the DNS?()
Refer to the exhibit. According to the equipment tab in Cisco UCS Manager, which is true?()