A. Server
B. End device
C. Node
D. Host
E. Virtual
您可能感興趣的試卷
你可能感興趣的試題
A. Sending all broadcasts
B. Receiving all traffic from upstream switches
C. Receiving broadcast traffic
D. Negotiating spanning tree with upstream switches
E. Learning MAC addresses from upstream switches
A. The Cisco VIC can create an unlimited number of Virtual NICs
B. The number of vNICs on the Cisco VIC that can be created is determined by the number of chassis uplinks
C. vNICs are created using software on the host operating system
D. The host operating system sees a vNIC as a physical PCIe device
E. The host operating system sees a vNIC as a sub-interface of a primary NIC
F. The Cisco VIC can create 1024 vNICs
A. Fibre Channel storage
B. UCS C-Series servers
C. NFS storage
D. UCS chassis
E. Other fabric interconnect
A. End-host mode is synonymous with NPV mode.
B. In end-host mode, only hard pinning of vHBAs to Fibre Channel uplink ports is allowed.
C. Making configuration changes between Fibre Channel switching mode and end-host mode is nondisruptive.
D. End-host mode is the default Fibre Channel switching mode.
A. In the blade BIOS
B. In the operating system
C. In the service profile
D. In the card option ROM
A. The QoS policy assigns a system class to the outgoing traffic for a vNIC or vHBA.
B. Flow-control policies determine whether the uplink Ethernet ports in a Cisco UCS environment send and receive IEEE 802.3x pause frames when the send buffer for a port fills.
C. If no system class is configured as CoS 0, the Fibre Channel system class is used.
D. The user can configure QoS for these system classes: platinum, gold, silver, best effort, Fibre Channel.
E. When configuring a system class, the type of adapter in a server may limit the maximum MTU supported.
A. boot policy and BIOS policy
B. disk scrub and boot policy
C. BIOS setting scrub, boot policy, and BIOS policy
D. disk scrub and BIOS setting scrub
A. name
B. best-effort
C. burst
D. rate
E. host control
A. logical configuration
B. all configuration
C. full state
D. system configuration
A. If disk scrub is enabled, all BIOS settings for the server are erased.
B. If disk scrub is enabled, all the data access on any local drives is destroyed.
C. If disk scrub is enabled, the LSI active RAID is destroyed but data is still preserved.
D. If disk scrub is disabled, all data on any local drives is preserved, including the local storage configuration.
E. If disk scrub is enabled, all data on any local drives is preserved, including the local storage configuration.
最新試題
On a Cisco Unified Computing System (UCS), which two statements regarding Ethanalyzer are true?()
When testing ICMP access to a functional load-balancing ACE VIP, it fails. What is the reason of this problem? ()
What is the use of an "all configuration" backup in Cisco UCS?()
Application Control Engine (ACE) can check the health of servers and server farms by configuring health probes (which are sometimes referred to as keepalives). A probe can be one of many types. Which are valid ACE probes? ()
Given the following output: san-port-channel 12 is up Hardware is Fibre Channel Port WWN is 24:0c:00:0d:ec:d3:5c:00 Admin port mode is NP, trunk mode is on Port mode is NP Port vsan is 1 Speed is 8 Gbps Member[1] : fc2/3 Member[2] : fc2/4 What does "Speed is 8 Gbps" indicate?()
Which of the following are supported in Cisco Global Site Selector? ()
What would be the cause for the following fault in UCS Manager?() "ether VIF x / xxx down, reason: ENM source pinning failed"
Which three statements are possible causes for the "fltAdaptorHostIfLink-down" fault in UCS Manager? ()
What is the purpose of this command in a Cisco Application Control Engine?() switch/Admin# show np 1 me-stats "-F0 v"
Which GSS "source access list" is used to allow access to GSS by clients when GSS is being used as the DNS?()