A. Only to Cisco Fibre Channel switches
B. Only to Cisco Fibre Channel switches in NPIV mode
C. To any Fibre Channel switch
D. Directly to storage arrays
E. Only to Nexus Switches
您可能感興趣的試卷
你可能感興趣的試題
A. Under the Admin tab on the FI
B. Under the Server tab in the service profile
C. Under the SAN tab on each VSAN
D. Under the Admin tab on the chassis
E. Under the SAN tab on the Fabric Interconnect
Given the following output：
san-port-channel 12 is up
Hardware is Fibre Channel
Port WWN is 24：0c：00：0d：ec：d3：5c：00
Admin port mode is NP， trunk mode is on
Port mode is NP Port vsan is 1
Speed is 8 Gbps
Member[1] ： fc2/3
Member[2] ： fc2/4
What does "Speed is 8 Gbps" indicate？（）
A. The speed of the slowest interface in the port channel
B. The combined speed of all interfaces configured in the port channel
C. The combined speed of all interfaces in the port channel that are up
D. The speed that can be achieved if all buffers are used
A. Server
B. End device
C. Node
D. Host
E. Virtual
A. Sending all broadcasts
B. Receiving all traffic from upstream switches
C. Receiving broadcast traffic
D. Negotiating spanning tree with upstream switches
E. Learning MAC addresses from upstream switches
A. The Cisco VIC can create an unlimited number of Virtual NICs
B. The number of vNICs on the Cisco VIC that can be created is determined by the number of chassis uplinks
C. vNICs are created using software on the host operating system
D. The host operating system sees a vNIC as a physical PCIe device
E. The host operating system sees a vNIC as a sub-interface of a primary NIC
F. The Cisco VIC can create 1024 vNICs
A. Fibre Channel storage
B. UCS C-Series servers
C. NFS storage
D. UCS chassis
E. Other fabric interconnect
A. End-host mode is synonymous with NPV mode.
B. In end-host mode， only hard pinning of vHBAs to Fibre Channel uplink ports is allowed.
C. Making configuration changes between Fibre Channel switching mode and end-host mode is nondisruptive.
D. End-host mode is the default Fibre Channel switching mode.
A. In the blade BIOS
B. In the operating system
C. In the service profile
D. In the card option ROM
A. The QoS policy assigns a system class to the outgoing traffic for a vNIC or vHBA.
B. Flow-control policies determine whether the uplink Ethernet ports in a Cisco UCS environment send and receive IEEE 802.3x pause frames when the send buffer for a port fills.
C. If no system class is configured as CoS 0， the Fibre Channel system class is used.
D. The user can configure QoS for these system classes： platinum， gold， silver， best effort， Fibre Channel.
E. When configuring a system class， the type of adapter in a server may limit the maximum MTU supported.
A. boot policy and BIOS policy
B. disk scrub and boot policy
C. BIOS setting scrub， boot policy， and BIOS policy
D. disk scrub and BIOS setting scrub
最新試題
An administrator is creating a service profile but receives an error when applying to a blade. The administrator checks the faults tab of the service profile and finds the following error （Refer to the exhibit）.What is the cause of this error？（）
Which two statements about end-host mode in SAN connectivity in a Cisco UCS environment are true？ （）
Refer to the exhibit.The Cisco UCS domain is operating in switching mode. A network administrator notices that no traffic is traversing the uplinks on Fabric Interconnect B （Path C）. Which actions might be used to change this behavior？（）
Which statement is true about "full state backup" in a Cisco Unified Computing System？（）
Which is true when describing a connection replication in Cisco ACE？（）
When will an "all configuration" backup be imported into the Cisco UCS Manager？（）
What is the use of an "all configuration" backup in Cisco UCS？（）
Which three statements are possible causes for the "fltAdaptorHostIfLink-down" fault in UCS Manager？ （）
Given a Cisco Unified Computing System， which is a valid port type in end-host mode？（）
Refer to the exhibit. According to the equipment tab in Cisco UCS Manager， which is true？（）