A. Hash address: Selects the server by using a hash value based on either the source or destination IP address, or both
B. Hash URL: Selects the server by using a hash value based on the requested URL
C. Hash MAC.Selects the server by using a hash value based on either the source or destination MAC address, or both
D. Hash header: Selects the server by using a hash value based on the HTTP header name
E. Hash IP: Selects the server using a hash value based on the IP address
您可能感興趣的試卷
你可能感興趣的試題
A. UCS-A# show pinning border-interfaces
B. UCS-B# show service-profile circuit
C. UCS-B(nxos)# show pinning server-interfaces
D. You must statically configure which uplink the blades should use, or you will not have connectivity.
A. An interface ’san-port-channel’ in NXOS
B. An interface ’port-channel’ in NXOS
C. An interface ’port-channel’ with ’mode fc’ configured
D. An interface ’fc-port-channel’ in NXOS
A. The fabric interconnects must be in end-host mode.
B. A pin group must be configured on the server tab in Cisco UCS Manager.
C. In the service profile for Server 1, vNIC 1 must be explicitly assigned to a pin group.
D. Server 1 cannot be configured to meet the requirement. A server can only be manually pinned to a single physical interface and not a port channel because of the LACP load-balancing algorithm.
E. Server 1 cannot be configured to meet the requirement. A server is either manually pinned to an uplink on both fabric interconnects or the server is automatically pinned, but not both.
Refer to the exhibit.
The Cisco UCS domain is operating in switching mode. A network administrator notices that no traffic is traversing the uplinks on Fabric Interconnect B (Path C).
Which actions might be used to change this behavior?()
A. Fix the port channel configuration between Fabric Interconnect B and Nexus 5548 B as the port channel IDs do not match.
B. Modify the bridge priority on the fabric interconnects so that one of the Nexus 5548s will always be the root bridge.
C. Modify the bridge priority on the Nexus 5548s so that one of them will always be the root bridge.
D. Modify the port priorities on the fabric interconnect uplinks (Paths B and C) so that they are a higher priority than ports Eth1/4 and Eth1/9 (Path D).
E. This is an invalid configuration as Cisco UCS fabric interconnects cannot be directly connected.
Refer to the exhibit.
According to the equipment tab in Cisco UCS Manager, which is true?()
A. A is an uplink port, B is a fabric port, C is a server port, D is a backplane port, E is a DCE interface, and F is a vNIC
B. A is an uplink port, B is a server port, C is a fabric port, D is a backplane port, E is a DCE interface, and F is a vNIC
C. A is an uplink port, B is a fabric port, C is a backplane port, D is a server port, E is a DCE interface, and F is a vNIC
D. A is an uplink port, B is a server port, C is a fabric port, D is a DCE interface, E is a backplane port, and F is a vNIC
E. A is an fabric port, B is a downlink port, C is an uplink port, D is a server port, E is a VIC interface, and F is a vNIC
Refer to the exhibit.
Your company requires a Cisco UCS configuration that will, at a minimum, allow the configuration in the provided exhibit.
Which Cisco UCS components will meet the requirement?()
A. Cisco UCS 6148, Cisco UCS 6248UP, or the Cisco UCS 6296UP fabric interconnects
B. Cisco UCS 2104XP Fabric Extender
C. Cisco UCS 2204XP or 2208XP Fabric Extenders
D. Cisco UCS M81KR Virtual Interface Card
E. Cisco UCS Virtual Interface Card 1280
F. Cisco UCS Virtual Interface Card 1240 with a port expander
A. Cisco UCS Manager 1.3(xx) or later and a pair of Nexus 2248 FEXes
B. Cisco UCS Manager 2.0(2xx) or later and a pair of Nexus 2232 FEXes
C. Two Cisco UCS 6100 Series or 6200 Series fabric interconnects
D. Two RJ45 Ethernet cables
E. The fabric interconnects must be in end-host mode
A. Uplink Ethernet ports or border ports
B. Appliance ports
C. Server ports
D. Fabric ports
E. Backplane ports
F. vEth interfaces
G. A Fabric Interconnect doesn’t learn MAC addresses in End Host mode. Pinning is used instead.
A. FabricSync is used to synchronize MAC addresses to an adjacent fabric interconnect after a server interface failover.
B. Gratuitous ARPs are sent on fabric interconnect uplinks after a server interface failover.
C. Fabric failover can be used on vNICs and vHBAs.
D. Fabric failover is configured as part of the service profile.
E. Fabric interconnects in end-host mode use fabric failover instead of spanning tree to provide redundancy on uplink ports.
A. Interface inbound-low handles Rx and Tx of low-priority control packet
B. Interface inbound-lo handles Rx and Tx of high-priority control packet
C. Interface inbound-low maps to internal interface eth3
D. Interface inbound-low maps to internal interface eth4
最新試題
On a Cisco Unified Computing System (UCS), which two statements regarding Ethanalyzer are true?()
What interface is created when an FC Port Channel is created on a Cisco Unified Computing System?()
In a Cisco Unified Computing System, where are SAN port channels connected to?()
Application Control Engine (ACE) can check the health of servers and server farms by configuring health probes (which are sometimes referred to as keepalives). A probe can be one of many types. Which are valid ACE probes? ()
Your company wants Server 1/eth0 (vNIC 1) configured so that it always uses Fabric Interconnect A Port Channel 1 (Po1) when it communicates with anything outside of the Cisco UCS domain. However, if vNIC 1 fails over to Fabric Interconnect B using fabric failover, then vNIC 1 can any uplink port on Fabric Interconnect B. Which statements are true? ()
What would be the cause for the following fault in UCS Manager?() "ether VIF x / xxx down, reason: ENM source pinning failed"
When will an "all configuration" backup be imported into the Cisco UCS Manager?()
An administrator is creating a service profile but receives an error when applying to a blade. The administrator checks the faults tab of the service profile and finds the following error (Refer to the exhibit).What is the cause of this error?()
Refer to the exhibit.Your company requires a Cisco UCS configuration that will, at a minimum, allow the configuration in the provided exhibit. Which Cisco UCS components will meet the requirement?()
Given the following output: san-port-channel 12 is up Hardware is Fibre Channel Port WWN is 24:0c:00:0d:ec:d3:5c:00 Admin port mode is NP, trunk mode is on Port mode is NP Port vsan is 1 Speed is 8 Gbps Member[1] : fc2/3 Member[2] : fc2/4 What does "Speed is 8 Gbps" indicate?()