A. It converges quickly.
B. OSPF is a classful routing protocol.
C. It uses cost to determine the best route.
D. It uses the DUAL algorithm to determine the best route.
E. OSPF routers send the complete routing table to all directly attached routers.
F. OSPF routers discover neighbors before exchanging routing information.
您可能感興趣的試卷
你可能感興趣的試題
A.10.15.32.17
B.17.15.66.128
C.66.55.128.1
D.135.1.64.34
E.129.33.192.192
F.192.168.5.63
A.172.31.17.4/30
B.172.31.51.16/30
C.172.31.64.0/18
D.172.31.80.0/22
E.172.31.92.0/22
F.172.31.192.0/18
A. The next routing update can be expected in 35 seconds.
B. The IP address 10.10.10.6 is configured on S0/1.
C. The IP address 10.10.10.8 is configured on S0/1.
D. This route is using the default administrative distance.
E. The 10.10.10.8 network is two hops away from this router.
A. the IP address of Switch 1
B. the MAC address of Switch 1
C. the IP address of Host C
D. the MAC address of Host C
E. the IP address of the router's E0 interface
F. the MAC address of the router's E0 interface
A.buffering
B.cut-through
C.windowing
D.congestion avoidance
E.load balancing
A.115.64.8.32
B.115.64.7.64
C.115.64.6.255
D.115.64.3.255
E.115.64.5.128
F.115.64.12.128
An administrator is unsuccessful in adding VLAN 50 to aswitch. While troubleshooting the problem, the administrator views the output of the show vtp status command, which is displayed in the graphic. What commands must be issued on this switch to add VLAN 50 to the database?()
A. Switch(config-if)# switchport access vlan 50
B. Switch(vlan)# vtp server
C. Switch(config)# config-revision 20
D. Switch(config)# vlan 50 name Tech
E. Switch(vlan)# vlan 50
F. Switch(vlan)# switchport trunk vlan 50
A. It supports VLSM.
B. It is used to route between autonomous systems.
C. It confines network instability to one area of the network.
D. It increases routing overhead on the network.
E. It allows extensive control of routing updates.
F. It is simpler to configure than RIP v2.
A. hello packets
B. SAP messages sent by other routers
C. LSAs from other routers
D. beacons received on point-to-point links
E. routing tables received from other link-state routers
F. TTL packets from designated routers
A. Each OSPF area requires a loopback interface to be configured.
B. Areas may be assigned any number from 0 to 65535.
C. Area 0 is called the backbone area.
D. Hierarchical OSPF networks do not require multiple areas.
E. Multiple OSPF areas must connect to area 0.
F. Single area OSPF networks must be configured in area 1.
最新試題
Which encapsulation type is a Frame Relay encapsulation type that is supported by Cisco routers?()
Which Cisco IOS diagnostics command can disrupt the operation of a router under high-load conditions?()
Which statement describes the rule of split horizon?()
Which protocol reduces administrative overhead in a switched network by allowing the configuration of a new VLAN to be distributed to all the switches in a domain?()
A router receives information about network 192.168.10.0/24 from multiple sources.What will the router consider the most reliable information about the path to that network?()
How are VTP advertisements delivered to switches across the network?()
Which cisco ios command can help to determine the timing of various debug events,relative to each other,when you are debugging a complicated router issue?()
What is the result of issuing the frame-relay map ip 192.168.1.2 202 broadcast command?()
Which command displays the CHAP authentication process as it occurs between two routers?()
What is the subnetwork address for a host with the IP address 201.100.5.68/28?()