A. 201.100.5.0
B. 201.100.5.32
C. 201.100.5.64
D. 201.100.5.65
E. 201.100.5.31
F. 201.100.5.1
您可能感興趣的試卷
你可能感興趣的試題
A. Only router can split boundaries(horizons)between concentric networks.
B. All distance vector protocols require fall routes that may cause momentary loops as the topology changes.
C. Networks can only remain fully converged if all information about routes is sent out all active interfaces.
D. Information about a route should not be sent back in the direction from which the original update came.
E. Each AS must keep routing tables converged to prevent dead routes from being advertised across the AS boundary.
A. Router#copy tftp flash
B. Router(config)#restore flash
C. Router(config)#repair flash
D. Router#copy flash run
E. Router>copy start flash
F. Router#copy start flash
A. 255.255.240.0
B. 255.255.248.0
C. 255.255.252.0
D. 255.255.254.0
E. 255.255.255.0
F. 255.255.255.192
A. IP address:192.168.20.14 Subnet Mask:255.255.255.248 Default Gateway:192.168.20.9
B. IP address:192.168.20.254 Subnet Mask:255.255.255.0 Default Gateway:192.168.20.1
C. IP address:192.168.20.30 Subnet Mask:255.255.255.248 Default Gateway:192.168.20.25
D. IP address:192.168.20.30 Subnet Mask:255.255.255.240 Default Gateway:192.168.20.17
E. IP address:192.168.20.30 Subnet Mask:255.255.255.240 Default Gateway:192.168.20.25
A. STP
B. VTP
C. GVRP
D. SNMP
E. DHCP
A network administrator is trying to add a new router into an established OSPF network.The networks attached to the new router do not appear in the routing tables of the other OSPF routers.Given the information in the partial configuration shown below,what configuration error is causing this problem?()
Router(config)#router ospf 1
Router(config-router)#network 10.0.0.0 255.0.0.0 area 0
A. The process id is configured improperly
B. The OSPF area is configured improperly
C. The network wildcard mask is configured improperly
D. The network number is configured improperly
E. The AS is configured improperly
F. The network subnet mask is configuerd improperly
A. the IP address of the first Fast Ethernet interface
B. the IP address of the console management interface
C. the highest IP address among its active interfaces
D. the lowest IP address among its active interfaces
E. the priority value until a loopback interface is configured
A. IBSS
B. BSS
C. ESS
D. SSID
The network administrator cannot to switch 1 over a telnet session,although the hosts attached to switch 1 can ping the interface Fa0/0 of the router.Given the information in the graphic and assuming that the router and switch2 are configured properly,which of the following commands should be issued on switch 1 to correct this problem?()
A. Switch1(config)# i nterface fa0 /1 Switch1(config-if)# ip address 192.168.24.3.255.255.255.0
B. Switch1 (config)#interface fa0/1 Switch1 (config-if)# switchport mode trunk
C. Switch 1 (config)# i nterface fa0 /1 Switch1 (config-if)# duplex full Switch1 (config-if)# speed 100
D. Switch1 (config-if)# default-gateway 192.168.24.1
E. Switch1 (config)# line con 0 Switch1(config-line)# password cisco Switch1 (config-line)#login
A. 192.168.252.8 255.255.255.248
B. 192.168.252.8 255.255.255.252
C. 192.168.252.16 255.255.255.240
D. 192.168.252.0 255.255.255.252
E. 192.168.252.16 255.255.255.252
最新試題
Which command is used to display the collection of OSPF link states?()
If all OSPF routers in a single area are configured with the same priority value,what value dose a router use for the ODPF router ID in the absence of a loopback interface?()
Which statement describes the rule of split horizon?()
Three switches are connected to one anther via trunk ports.Assuming the default switch configuration,which switch is elected as the root bridge for the spanning-tree instance of vlan 1?()
On which options are standard access list based?()
Which device might be installed at a branch office to enable and manage an IPsec site-to-site VPN?()
Which command encrypts all plaintext passwords?()
Which command displays the CHAP authentication process as it occurs between two routers?()
When you are troubleshooting an ACL issue on a router,which command can help you to verify which interfaces are affected by the ACL?()
Which protocol reduces administrative overhead in a switched network by allowing the configuration of a new VLAN to be distributed to all the switches in a domain?()