A.OSNR
B.dispersion
C.light skew
D.attenuation
您可能感興趣的試卷
你可能感興趣的試題
A.none
B.one
C.two
D.three
E.four
Click the Exhibit button. What is the maximum allowable loss budget between the ONS 15216 Mux (left side) composite output and the ONS 15216 Demux (right side) composite input, with the optical values given in the exhibit? （）(Assume the worst case loss of 4.5 dB for 15216 200 GHz Mux/Demux and ignore power penalties or extra margin.)
A.15dB
B.17dB
C.21dB
D.26dB
E.27dB
A. All "Add" channels require uniform power levels.
B. The flexibility of wavelengths per OADM is limited.
C. It is easier to balance "Pass-Through" and "Add" channels.
D. There is lower pass-through loss using multi-channel OADMs.
E. You can extract a single channel without dropping other channels.
Click the Exhibit button. Given the following parameters: transmitter output (min): -2 dBm receiver input (min): -28 dBm 15216 Mux and Demux loss: 4.5 dB 16 channels maximum In which sites shown in the exhibit could the 15216 EDFAs be placed to minimize the number of EDFAs needed?（）
A. Locations B, C only
B. Locations A, B, C only
C. Locations A, B, D only
D. Locations B, C, D only
E. Locations A, B, C, D
A. The ONS 15216 OADM can be provisioned to add/drop one, two, or four channels via Cisco Transport Manager (CTM).
B. The ONS 15216 OADM consists only of a four-channel module, and the number of ports utilized determines whether it is a one, two, or four channel OADM.
C. Three separate OADM modules are available for one, two, and four channels. The wavelengths to be dropped and added are programmable via Cisco Transport Manager (CTM).
D. The ONS 15216 OADM consists only of a single-channel module. Two-channel and four-channel support is available by stacking the single-channel module.
E. The ONS 15216 OADM is available in one, two, four channels. There are 32 single-channel OADM modules, 16 two-channel OADM modules, and 8 four-channel OADM modules.
Click the Exhibit button. The exhibit shows a 15454/15216 DWDM system and alarm indications. What are two possible sources of trouble shown in the system?（） (Choose two.)
A. fiber failure between Sites A and d
B. EDFA failure at Site A (clockwise direction)
C. EDFA failure at Site C (clockwise direction)
D. 15216 multiplexer at Site A (counter-clockwise direction)
E. OADM pass-through (West "OUT") failure at site D (clockwise)
F. wavelengths 1 and 3 transmitter failures at Site A (clockwise direction)
A. dispersion
B. Optical SNR
C. span attenuation
D. four wave mixing
E. receiver sensitivity
A. the K1 SONET byte； the K2 SONET byte
B. the K2 SONET byte；the K1 SONET byte
C. transmitter switching；receiver detection
D. Line Overhead bytes；Path Overhead bytes
E. Path Overhead bytes；Line Overhead bytes
A. SDH circuit over a SONET network delivering it as an SDH signal
B. SDH circuit over a SONET network delivering it as a SONET signal
C. SONET circuit over an SDH network delivering it as an SDH signal
D. SONET circuit over an SDH network delivering it as a SONET signal
A. trunking
B. squelching
C. nodal bypass
D. bridge and roll
E. node failure insertion
最新試題
What three in combination are factors that can cause four-wave mixing in fiber-optic cables? （）(Choose three.)
What are three relevant design considerations when using the 15216 EDFA? （）(Choose three.)
Which three technologies are used to reduce chromatic dispersion accumulation in fiber-optic transmission systems? （）(Choose three.)
On an ONS 15454 node you can tunnel an （）.
UPSR protection switching is initiated by （）, while BLSR is initiated by （）.
Given the formula: (Fiber Attenuation * Km) + (Splice Attenuation * # of Splices) + (Connector Attenuation * # of Connectors) + (Optical Fiber or OADM) + Buffer(Fiber aging)) With regard to SONET/SDH optical calculations, what will the given formula provide?（）
How is UPSR and BLSR traffic rerouted during a protection switch when a complete fiber cable cut occurs?（）
If node 2 is accepting line timing from node 1, node 2 will send （）to node 1 as its SSM message.
The dispersion of a non-zero dispersion shifted fiber is 6 ps/nm*km at 1550 nm and 10 ps/nm*km at 1610 nm. What is the minimum dispersion compensation required if an L-Band DWDM signal travels through 200 km of fiber and has a dispersion tolerance of 1800 ps/nm?（）
What protection method is used in 4F BLSR networks?（）