A Cisco Aironet 1020 controller-based access point has been connected to a Catalyst 3550-24 PWRSwitch. However， when it is powered up， the access point fails.
What has caused this problem？（）
A.access point does not support 802.11h
B.incorrect switch power supply
C.switch port is not enabled
D.switch does not support 802.3af
E.access point has not been initialized with the primary controller
您可能感興趣的試卷
你可能感興趣的試題
A.Acceptance Test Plan
B.Change Management
C.Incident Management
D.Configuration Management
A.Ongoing Support Handoff Meeting
B.Staff Training
C.Detailed Design Development
D.Staging and System Migration
On a standalone access point， client association using EAP-Cisco Wireless （Cisco-LEAP） is failing，but association using EAP-PEAP is functioning.
What needs to be enabled on the standalone accesspoint to correct this issue？（）
A.network EAP
B.open authentication plus MAC
C.open authentication plus EAP
D.a shared key
You have just finished aligning a Cisco Aironet 1400 Series Wireless Bridge link using installationmode.When you set the link back to operational mode you loose association to the root bridge.
Which action will correct the problem？（）
A.Configure the bridge to force infrastructure devices to associate only to the SSID parameter.
B.Enable passwords on both bridges.
C.Configure the distance parameter value.
D.Configure the proper channel.
You are troubleshooting a one-way call problem with a Cisco 7920 wireless IP phone on a standalone WLAN.
What may have caused this problem？（）
A.The minimum data rate is not set to 11 Mbps.
B.Publicly Secure Packet forwarding is enabled.
C.The access point is set to the least congested channel.
D.An address resolution protocol has been disabled.
On a Cisco Aironet 1130AG Series standalone access point， the status LED is dark blue and blinking.
What does this indicate？（）
A.The internal radio has failed.
B.A firmware upgrade is in progress.
C.An access point buffer overflow is occurring.
D.The access point is booting.
In a deployment using standalone access points， clients set up to authenticate with EAP-PEAP orEAP-Cisco Wireless （Cisco-LEAP） cannot authenticate. When you inspect the Failed Attempts reporton the Cisco Secure ACS， you find this error： "Unknown network access server NAS."
Which problem may have caused this failure？（）
A.misconfigured IP address of the AAA server on the access point
B.misconfigured EAP type on the access point
C.misconfigured IP address of the access point on the AAA server
D.misconfigured EAP type on the AAA server
A.router （config-ssid）# guest-mode
B.router （config-ssid）# advertise
C.router （config-ssid）# enable
D.router （config-ssid）# broadcast
Your customer has deployed a Cisco Wireless Location Appliance within its warehouseenvironment.
However， employees there have been experiencing problems when tracking objects using activeRFID tags.The RFID tag data is not being collected.
On which device would you verify that RFIDs have been enabled？（）
A.access point
B.location manager
C.wireless controller
D.Cisco WCS
A.partners having a discussion with customers about the minimum service components needed to successfully deploy a wireless solution
B.customers determining a competitor’s strategy for adopting advanced technologies
C.partners choosing the right products for their customers
D.customers choosing the right products for their network
E.customers defining the correct strategy for advanced technology adoption
最新試題
An REAP was supporting 16 WLANs， but now it only supports one.What happened to cause the change？（）
You are configuring an RF group of controllers that coordinate Radio Resource Management calculations.What is the maximum number of WLAN controllers that you can add？（）
You review the Failed Attempts logs on an AAA server and find： "unknown network access servererror." Which failure could produce this error？（）
You are troubleshooting a one-way call problem with a Cisco 7920 wireless IP phone on a standalone WLAN.What may cause this problem？（）
You have been called upon to add location-based services into an existing controller-basedwireless design which primarily encompasses handheld devices such as barcode scanners and Cisco7920 wireless IP phones.In which mode should you deploy the additional access points to achievethe density required without excessive co-channel interference？（）
A client roams from H-REAP AP1 to H-REAP AP2. The client is unable to associate to H-REAP AP2.H-REAP AP2 has six other clients associated to it， which continue to pass traffic.What has causedthis problem？（）
Clients using Cisco-LEAP and EAP-FAST authentication are having no problems logging on to thewireless network， but clients using PEAP are failing to log on.Which situation would result in thistype of problem？（）
You are installing a Cisco Aironet 1000 Series controller-based access point. When you boot it， allthe LEDs on the access point blink together.What does this indicate about the access point？（）
Static WEP is configured on the access point. You are authenticated and associated to the accesspoint but are unable to obtain an IP address.Which of the following will cause this problem？（）
A mobility group is created by a Cisco WLCM and 4402 Series Wireless LAN Controller. A client thatis anchored on the Cisco WLCM roams to an access point on the 4402 controller. You then run adebug command on the 4402 controller.Which message would best describe the establishment ofthe tunnel from the foreign controller’s perspective？（）