Your customer has deployed a Cisco Wireless Location Appliance within its warehouseenvironment.
However, employees there have been experiencing problems when tracking objects using activeRFID tags.The RFID tag data is not being collected.
On which device would you verify that RFIDs have been enabled?()
A.access point
B.location manager
C.wireless controller
D.Cisco WCS
您可能感興趣的試卷
你可能感興趣的試題
A.partners having a discussion with customers about the minimum service components needed to successfully deploy a wireless solution
B.customers determining a competitor’s strategy for adopting advanced technologies
C.partners choosing the right products for their customers
D.customers choosing the right products for their network
E.customers defining the correct strategy for advanced technology adoption
You are using standalone Cisco Aironet 1400 Series Wireless Bridges for a nine-mile point-to-pointwireless link between two buildings.
Which distance setting should you use for the bridgeconfigured as theroot?()
A.20 km [12.4 miles]
B.10 km [6.2 miles]
C.5 km [3.1 miles]
D.25 km [15.5 miles]
E.15 km [9.3 miles]
EAP-FAST provides a secure tunnel during Phase One to protect the user’s authentication credentials.
Which of these entities initializes the secure tunnel?()
A.x.509 certificate
B.generic token card
C.preshared key
D.Protected Access Credential
Your customer has deployed a Cisco Wireless Location Appliance within its warehouseenvironment.
However, employees there have been experiencing problems when tracking objects using activeRFID tags.The RFID beacon rate is 10 seconds and you have discovered an issue with the RFID timeout value.
Where and how should the RFID value be changed?()
A.on the Cisco WCS, to 95 seconds
B.on the wireless controller, to 45 seconds
C.on the wireless controller, to 95 seconds
D.on the Cisco WCS, to 45 seconds
You are installing a Cisco Aironet 1000 Series controller-based access point. When you boot it, allthe LEDs on the access point blink together.
What does this indicate about the access point?()
A.duplicate IP address
B.code upgrade in progress
C.normal operation
D.searching for primary controller
A.IPX
B.IP
C.UDP
D.TCP
A.14
B.15
C.17
D.16
A.Location Appliance
B.controller-based access points
C.wireless clients
D.Wireless Control System
E.wireless controllers
A.Mirror
B.Rogue Detector
C.Sniffer
D.Monitor
A client roams from H-REAP AP1 to H-REAP AP2. The client is unable to associate to H-REAP AP2.H-REAP AP2 has six other clients associated to it,which continue to pass traffic.
What has causedthis problem?()
A.H-REAP AP1 has reached its client limit.
B.H-REAP AP2 has reached its client limit.
C.H-REAP AP2 lost its connection to the controller.
D.H-REAP AP1 lost its connection to the controller.
最新試題
You are troubleshooting a problem with a Cisco 7920 wireless IP phone on a standalone WLAN.The phone rings but, when you answer, the call is dropped.What may cause this problem?()
You are troubleshooting a one-way call problem with a Cisco 7920 wireless IP phone on a standalone WLAN.What may cause this problem?()
When configuring a WLAN controller for a voice application using Cisco 7920 wireless IP phones,which two general control settings should you select?()
You are configuring a wireless LAN controller for QoS.Which 802.11e user priority tag should you apply to voice applications?()
Which of the following accurately represents the functionality of a lightweight access point configured to operate in sniffer AP mode?()
You want to dynamically assign users to an 802.1Q VLAN as a result of their authentication. Inorder to accomplish this.Which two IETF RADIUS attributes should you configure on the CiscoSecure ACS? ()
When configuring Cisco Secure ACS to support wireless EAP authentication, which device must be configured as a AAA client?()
You have just finished aligning a Cisco Aironet 1400 Series Wireless Bridge link using installationmode. When you set the link back to operational mode you loose association to the root bridge.Which action will correct the problem?()
You are trying to change the polling parameters used by the location manager via the Cisco WCS,and your request is being denied. What is wrong?()
Static WEP is configured on the access point. You are authenticated and associated to the accesspoint but are unable to obtain an IP address.Which of the following will cause this problem?()