A.Wireless Control System
B.Wireless clients
C.Wireless controllers
D.Control-based access points
E.Location Appliance
您可能感興趣的試卷
你可能感興趣的試題
On a Cisco Aironet 802.11 a/b/g wireless LAN client adapter，the status LED and activity LED are alternating on and off.
What does this indicate？（）
A.The client card has failed.
B.The client card is not associated to the network.
C.The driver has been installed incorrectly.
D.The client card has awakened from power-save mode.
You have a very few Cisco 7920 wireless IP phones on your network， but lots of wireless laptops.You want to increase the bandwidth available for the laptops by decreasing the bandwidth reserved for the Cisco 7920 phones.
What is the lowest percentage of voice-allocated bandwidthyou can select on the WLAN controller？（）
A.25 percent
B.40 percent
C.55 percent
D.75 percent
You are installing a Cisco Aironet 1000 Series controller-based access point. When you boot it， allthe LEDs on the access point blink together.
What does this indicate about the access point？（）
A.normal operation
B.duplicate IP address
C.code upgrade in progress
D.searching for primary controller
You are configuring an RF group of controllers that coordinate Radio Resource Management calculations.
What is the maximum number of WLAN controllers that you can add？（）
A.12
B.17
C.20
D.24
A mobility group is created by a Cisco WLCM and 4402 Series Wireless LAN Controller. A client thatis anchored on the Cisco WLCM roams to an access point on the 4402 controller. You then run adebug command on the 4402 controller.
Which message would best describe the establishment ofthe tunnel from the foreign controller’s perspective？（）
A.Transmit Mobile Anchor Export message
B.Receive Mobile Anchor Export message
C.Transmit Plumbing duplex mobility tunnel message
D.Receive Plumbing duplex mobility tunnel message
A.4
B.8
C.16
D.32
The IOS of a North American Cisco Aironet 1130AG Series standalone access point has becomecorrupt. You must therefore reload the TFTP firmware.
Before you press and hold the MODEbutton， you should verify that the file name is which of the following？（）
A.c1130-k9w7-tar.boot
B.c1130-k9w7-tar.default
C.c1130-k9w7-tar.recover
D.c1130-k9w7-tar.123-7.JA1.tar
You are troubleshooting a problem with a Cisco 7920 wireless IP phone on a standalone WLAN.The phone rings but， when you answer， the call is dropped.
What may cause this problem？（）
A.The minimum data rate is not set to 11 Mbps.
B.An address resolution protocol is enabled.
C.Publicly Secure Packet forwarding is enabled.
D.The access point is set to the least congested channel.
A.45
B.60
C.15
D.30
最新試題
Static WEP is configured on the access point. You are authenticated and associated to the accesspoint but are unable to obtain an IP address.Which of the following will cause this problem？（）
Which of the following parameter sets must be configured on the Cisco Wireless Location Appliance？（）
When configuring Cisco Secure ACS to support wireless EAP authentication， which device must be configured as a AAA client？（）
Which protocol does the RADIUS server use inside the secure tunnel of EAP-FAST to authenticatethe client when one-time passwords are in use？（）
You have been called upon to add location-based services into an existing controller-basedwireless design which primarily encompasses handheld devices such as barcode scanners and Cisco7920 wireless IP phones.In which mode should you deploy the additional access points to achievethe density required without excessive co-channel interference？（）
You are troubleshooting a problem with a Cisco 7920 wireless IP phone on a standalone WLAN.The phone rings but， when you answer， the call is dropped.What may cause this problem？（）
You are trying to change the polling parameters used by the location manager via the Cisco WCS，and your request is being denied. What is wrong？（）
You are troubleshooting a problem with a Cisco 7920 wireless IP phone that is causing the phoneto drop calls. The problem appears to be roaming bandwidth issue. In order to verify what kind ofissue it is， you decide to increase the bandwidth reserve for roaming on the WLAN controller tomaximum.What level do you set the bandwidth to？（）
You are charges with implementing a secure wireless installation which will provide Internet accessto client devices but will not allow communications between wireless clients.In addition to implementing PSPF or peer-to-peer blocking on the wireless side，which of the following actionsshould you perform on the wired infrastructure？（）
You are configuring an RF group of controllers that coordinate Radio Resource Management calculations.What is the maximum number of WLAN controllers that you can add？（）