A.router (config-ssid)# guest-mode
B.router (config-ssid)# advertise
C.router (config-ssid)# enable
D.router (config-ssid)# broadcast
您可能感興趣的試卷
你可能感興趣的試題
Your customer has deployed a Cisco Wireless Location Appliance within its warehouseenvironment.
However, employees there have been experiencing problems when tracking objects using activeRFID tags.The RFID tag data is not being collected.
On which device would you verify that RFIDs have been enabled?()
A.access point
B.location manager
C.wireless controller
D.Cisco WCS
A.partners having a discussion with customers about the minimum service components needed to successfully deploy a wireless solution
B.customers determining a competitor’s strategy for adopting advanced technologies
C.partners choosing the right products for their customers
D.customers choosing the right products for their network
E.customers defining the correct strategy for advanced technology adoption
You are using standalone Cisco Aironet 1400 Series Wireless Bridges for a nine-mile point-to-pointwireless link between two buildings.
Which distance setting should you use for the bridgeconfigured as theroot?()
A.20 km [12.4 miles]
B.10 km [6.2 miles]
C.5 km [3.1 miles]
D.25 km [15.5 miles]
E.15 km [9.3 miles]
EAP-FAST provides a secure tunnel during Phase One to protect the user’s authentication credentials.
Which of these entities initializes the secure tunnel?()
A.x.509 certificate
B.generic token card
C.preshared key
D.Protected Access Credential
Your customer has deployed a Cisco Wireless Location Appliance within its warehouseenvironment.
However, employees there have been experiencing problems when tracking objects using activeRFID tags.The RFID beacon rate is 10 seconds and you have discovered an issue with the RFID timeout value.
Where and how should the RFID value be changed?()
A.on the Cisco WCS, to 95 seconds
B.on the wireless controller, to 45 seconds
C.on the wireless controller, to 95 seconds
D.on the Cisco WCS, to 45 seconds
You are installing a Cisco Aironet 1000 Series controller-based access point. When you boot it, allthe LEDs on the access point blink together.
What does this indicate about the access point?()
A.duplicate IP address
B.code upgrade in progress
C.normal operation
D.searching for primary controller
A.IPX
B.IP
C.UDP
D.TCP
A.14
B.15
C.17
D.16
A.Location Appliance
B.controller-based access points
C.wireless clients
D.Wireless Control System
E.wireless controllers
A.Mirror
B.Rogue Detector
C.Sniffer
D.Monitor
最新試題
Which protocol does the RADIUS server use inside the secure tunnel of EAP-FAST to authenticatethe client when one-time passwords are in use?()
The IOS of a North American Cisco Aironet 1130AG Series standalone access point has becomecorrupt. You must therefore reload the TFTP firmware.Before you press and hold the MODEbutton, you should verify that the file name is which of the following?()
You are troubleshooting a problem with a Cisco 7920 wireless IP phone that is causing the phoneto drop calls. The problem appears to be roaming bandwidth issue. In order to verify what kind ofissue it is, you decide to increase the bandwidth reserve for roaming on the WLAN controller tomaximum.What level do you set the bandwidth to?()
A client roams from H-REAP AP1 to H-REAP AP2. The client is unable to associate to H-REAP AP2.H-REAP AP2 has six other clients associated to it, which continue to pass traffic.What has causedthis problem?()
On a Cisco Aironet 802.11 a/b/g wireless LAN client adapter,the status LED and activity LED are alternating on and off.What does this indicate?()
A mobility group is created by a Cisco WLCM and 4402 Series Wireless LAN Controller. A client thatis anchored on the Cisco WLCM roams to an access point on the 4402 controller. You then run adebug command on the 4402 controller.Which message would best describe the establishment ofthe tunnel from the foreign controller’s perspective?()
You have a very few Cisco 7920 wireless IP phones on your network, but lots of wireless laptops.You want to increase the bandwidth available for the laptops by decreasing the bandwidth reserved for the Cisco 7920 phones.What is the lowest percentage of voice-allocated bandwidthyou can select on the WLAN controller?()
You are troubleshooting a problem with a Cisco 7920 wireless IP phone on a standalone WLAN.The phone rings but, when you answer, the call is dropped.What may cause this problem?()
You are installing a Cisco 4402 Series Wireless LAN Controller.What type of interface is used on the uplink port?()
You want to dynamically assign users to an 802.1Q VLAN as a result of their authentication. Inorder to accomplish this.Which two IETF RADIUS attributes should you configure on the CiscoSecure ACS? ()