In a deployment using standalone access points, clients set up to authenticate with EAP-PEAP orEAP-Cisco Wireless (Cisco-LEAP) cannot authenticate. When you inspect the Failed Attempts reporton the Cisco Secure ACS, you find this error: "Unknown network access server NAS."
Which problem may have caused this failure?()
A.misconfigured IP address of the AAA server on the access point
B.misconfigured EAP type on the access point
C.misconfigured IP address of the access point on the AAA server
D.misconfigured EAP type on the AAA server
您可能感興趣的試卷
你可能感興趣的試題
A.router (config-ssid)# guest-mode
B.router (config-ssid)# advertise
C.router (config-ssid)# enable
D.router (config-ssid)# broadcast
Your customer has deployed a Cisco Wireless Location Appliance within its warehouseenvironment.
However, employees there have been experiencing problems when tracking objects using activeRFID tags.The RFID tag data is not being collected.
On which device would you verify that RFIDs have been enabled?()
A.access point
B.location manager
C.wireless controller
D.Cisco WCS
A.partners having a discussion with customers about the minimum service components needed to successfully deploy a wireless solution
B.customers determining a competitor’s strategy for adopting advanced technologies
C.partners choosing the right products for their customers
D.customers choosing the right products for their network
E.customers defining the correct strategy for advanced technology adoption
You are using standalone Cisco Aironet 1400 Series Wireless Bridges for a nine-mile point-to-pointwireless link between two buildings.
Which distance setting should you use for the bridgeconfigured as theroot?()
A.20 km [12.4 miles]
B.10 km [6.2 miles]
C.5 km [3.1 miles]
D.25 km [15.5 miles]
E.15 km [9.3 miles]
EAP-FAST provides a secure tunnel during Phase One to protect the user’s authentication credentials.
Which of these entities initializes the secure tunnel?()
A.x.509 certificate
B.generic token card
C.preshared key
D.Protected Access Credential
Your customer has deployed a Cisco Wireless Location Appliance within its warehouseenvironment.
However, employees there have been experiencing problems when tracking objects using activeRFID tags.The RFID beacon rate is 10 seconds and you have discovered an issue with the RFID timeout value.
Where and how should the RFID value be changed?()
A.on the Cisco WCS, to 95 seconds
B.on the wireless controller, to 45 seconds
C.on the wireless controller, to 95 seconds
D.on the Cisco WCS, to 45 seconds
You are installing a Cisco Aironet 1000 Series controller-based access point. When you boot it, allthe LEDs on the access point blink together.
What does this indicate about the access point?()
A.duplicate IP address
B.code upgrade in progress
C.normal operation
D.searching for primary controller
A.IPX
B.IP
C.UDP
D.TCP
A.14
B.15
C.17
D.16
A.Location Appliance
B.controller-based access points
C.wireless clients
D.Wireless Control System
E.wireless controllers
最新試題
A Cisco WCS version 4.0 has been installed on a server with a dual Pentium 3.0 GHz processor,4GB RAM, and an 80 GB hard drive. A location appliance has been incorporated into the networkand is being monitored by the Cisco WCS. There are 3000 devices to be tracked but not all of themare being tracked on the Cisco WCS.What can be done to correct the problem?()
When configuring a WLAN controller for a voice application using Cisco 7920 wireless IP phones,which two general control settings should you select?()
You review the Failed Attempts logs on an AAA server and find: "unknown network access servererror." Which failure could produce this error?()
A client roams from H-REAP AP1 to H-REAP AP2. The client is unable to associate to H-REAP AP2.H-REAP AP2 has six other clients associated to it, which continue to pass traffic.What has causedthis problem?()
Static WEP is configured on the access point. You are authenticated and associated to the accesspoint but are unable to obtain an IP address.Which of the following will cause this problem?()
You are troubleshooting a one-way call problem with a Cisco 7920 wireless IP phone on a standalone WLAN.What may cause this problem?()
You are installing a Cisco 4402 Series Wireless LAN Controller.What type of interface is used on the uplink port?()
Clients using Cisco-LEAP and EAP-FAST authentication are having no problems logging on to thewireless network, but clients using PEAP are failing to log on.Which situation would result in thistype of problem?()
On a Cisco Aironet 1240AG Series standalone access point, the radio LED is dark blue and blinking,but the status LED and Ethernet LED are both off.What does this indicate?()
You want to dynamically assign users to an 802.1Q VLAN as a result of their authentication. Inorder to accomplish this.Which two IETF RADIUS attributes should you configure on the CiscoSecure ACS? ()