A.protect (drop packets with unknown source addresses)
B.restrict (increment SecurityViolation counter)
C.shut down (access or trunk port)
D.transition (the access port to a trunking port)
您可能感興趣的試卷
你可能感興趣的試題
A.Test the design on a pilot network for expected results prior to implementing on the production network.
B.Run a network audit to determine types of traffic in use on the network.
C.Launch campus updates into the production network and monitor impact to see if configuration changes are needed.
D.Create an interruption of data flow to determine test "back-door" access methods.
A.a detailed physical and logical topology
B.a cost analysis of the implemented solution
C.detailed logs from the AAA and SNMP servers
D.results from audit testing of the implemented solution
A.having alternative addressing and VLAN schemes
B.having a rollback plan in case of unwanted or unexpected results
C.running a test script against all possible security threats to insure that the solution will mitigate all potential threats
D.isolating and testing each security domain individually to insure that the security design will meet overall requirements when placed into production as an entire system
A.a list of existing network applications currently in use on the network
B.network audit results to uncover any potential security holes
C.a planned Layer 2 design solution
D.a proof-of-concept plan
E.device configuration templates
A.detailed list of personnel assigned to each task within the plan
B.a Layer 2 spanning tree design topology
C.rollback guidelines
D.placing all unused access ports in VLAN 1 to proactively manage port security
E.enabling SNMP access to Cisco Discovery Protocol data for logging and forensic analysis
A.detailed VLAN information
B.an incident response plan
C.results of testing the new network configuration
D.an existing hierarchical network topology
E.a security policy for your organization
You are tasked with designing a security solution for your network.
What information should be gathered prior to designing the solution?()
A.a list of applications currently in use in the network
B.IP addressing design plans so that the network can be appropriately segmented to mitigate potential network threats
C.detailed security device specifications
D.results from pilot network testing
You are tasked with designing a security solution for your network.
What information should be gathered prior to designing the solution?()
A.IP addressing design plans so that the network can be appropriately segmented to mitigate potential network threats
B.detailed security device specifications
C.results from pilot network testing
D.results from a network audit
You are tasked with designing a security solution for your network.
What information should be gathered prior to designing the solution?()
A.IP addressing design plans so that the network can be appropriately segmented to mitigate potential network threats
B.a list of the customer requirements
C.detailed security device specifications
D.results from pilot network testing
Cat6500(config)# router ospf 1
Cat6500(config-router)# network 0.0.0.0 255.255.255.255 area 0
Cat6500(config-router)# nsf Cat6500(config-router)#end
Refer to the exhibit. The configuration is used to enable nonstop forwarding for OSPF on a Catalyst 6500 Series
Switch with redundant supervisor engines.
The default CEF configuration is unchanged. After testing, user traffic is interrupted and NSF is not operational.
What is the most likely reason? ()
A.CEF was not properly configured.
B.OSPF was not properly configured for graceful restart.
C.Stateful switchover was not correctly configured.
D.NSF for OSPF is only supported in area 0.
最新試題
Refer to the exhibit. LACP has been configured on Switch1 as shown. Which is the correct command set to configure LACP on Switch2?()
DS2 has not become the active device for Vlan103’s HSRP group even though all interfaces are active. As related to Vlan103’s HSRP group. What can be done to make the group function properly ? ()
What is the configured priority value of the Vlan105’s group on DS2 ?()
Which statement is correct about RSTP port roles?()
Refer to the exhibit. Switch S2 contains the default configuration. Switches S1 and S3 both have had the command spanning-tree mode rapid-pvst issued on them. What will be the result?()
Refer to the exhibit. Initially, LinkA is connected and forwarding traffic. A new LinkB is then attached between SwitchA and HubA. Which two statements are true about the possible result of attaching the second link?()
Refer to the exhibit. What will happen when one more user is connected to interface FastEthernet 5/1? ()
If G1/0/1 on DS1 is shutdown, what will be the current priority value of the Vlan105’s group on DS1 ?()
Which router redundancy protocol cannot be configured for interface tracking?()
What must be the same to make multiple switches part of the same Multiple Spanning Tree (MST)?()