A.a list of existing network applications currently in use on the network
B.network audit results to uncover any potential security holes
C.a planned Layer 2 design solution
D.a proof-of-concept plan
E.device configuration templates
您可能感興趣的試卷
你可能感興趣的試題
A.detailed list of personnel assigned to each task within the plan
B.a Layer 2 spanning tree design topology
C.rollback guidelines
D.placing all unused access ports in VLAN 1 to proactively manage port security
E.enabling SNMP access to Cisco Discovery Protocol data for logging and forensic analysis
A.detailed VLAN information
B.an incident response plan
C.results of testing the new network configuration
D.an existing hierarchical network topology
E.a security policy for your organization
You are tasked with designing a security solution for your network.
What information should be gathered prior to designing the solution?()
A.a list of applications currently in use in the network
B.IP addressing design plans so that the network can be appropriately segmented to mitigate potential network threats
C.detailed security device specifications
D.results from pilot network testing
You are tasked with designing a security solution for your network.
What information should be gathered prior to designing the solution?()
A.IP addressing design plans so that the network can be appropriately segmented to mitigate potential network threats
B.detailed security device specifications
C.results from pilot network testing
D.results from a network audit
You are tasked with designing a security solution for your network.
What information should be gathered prior to designing the solution?()
A.IP addressing design plans so that the network can be appropriately segmented to mitigate potential network threats
B.a list of the customer requirements
C.detailed security device specifications
D.results from pilot network testing
Cat6500(config)# router ospf 1
Cat6500(config-router)# network 0.0.0.0 255.255.255.255 area 0
Cat6500(config-router)# nsf Cat6500(config-router)#end
Refer to the exhibit. The configuration is used to enable nonstop forwarding for OSPF on a Catalyst 6500 Series
Switch with redundant supervisor engines.
The default CEF configuration is unchanged. After testing, user traffic is interrupted and NSF is not operational.
What is the most likely reason? ()
A.CEF was not properly configured.
B.OSPF was not properly configured for graceful restart.
C.Stateful switchover was not correctly configured.
D.NSF for OSPF is only supported in area 0.
To initiate testing,
which port does a Cisco IOS IP SLA source use to send a control message to an IP SLA responder? ()
A.UDP port 2020
B.UDP port 1967
C.TCP port 2020
D.ICMP port 1967
A.required at the destination to implement Cisco IOS IP SLA services
B.improves measurement accuracy
C.required for VoIP jitter measurements
D.provides security on Cisco IOS IP SLA messages via LEAP or EAP-FAST authentication
E.responds to one Cisco IOS IP SLA operation per port
F.stores the resulting test statistics
A.only implemented between Cisco source and destination-capable devices
B.statistics provided by syslog, CLI, and SNMP
C.measures delay, jitter, packet loss, and voice quality
D.only monitors VoIP traffic flows
E.provides active monitoring
F.provides passive monitoring
A.Test major changes before deployment and defer minor changes until during deployment.
B.Document and verify rollback procedures.
C.Ensure consistency of code versions across the network.
D.Progressively modify procedures and documentation during implementation.
最新試題
Refer to the exhibit. For what purpose is the command show ip cef used?()
What is the configured priority value of the Vlan105’s group on DS2 ?()
Which three statements about STP timers are true?()
Refer to the exhibit. LACP has been configured on Switch1 as shown. Which is the correct command set to configure LACP on Switch2?()
Which two statements about the various implementations of STP are true?()
Refer to the exhibit. Switch S2 contains the default configuration. Switches S1 and S3 both have had the command spanning-tree mode rapid-pvst issued on them. What will be the result?()
Refer to the exhibit. The command switchport mode access is issued on interface FastEthernet0/13 on switch CAT1. What will be the result?()
Refer to the exhibit. Which statement is true about the output?()
Refer to the exhibit. On the basis of the output of the show spanning-tree inconsistentports command, which statement about interfaces FastEthernet 0/1 and FastEthernet 0/2 is true?()
Which two statements are true about BPDU port-guard and BPDU filtering?()