A.Depends on the number of switches in the spanning tree domain
B.50 seconds
C.15 seconds
D.Until the root directs it to start forwarding
E.20 seconds
F.Depends on the pott speed
您可能感興趣的試卷
你可能感興趣的試題
A.show ip bgp neighbors
B.debug ip bgp updates
C.show ip route bgp
D.show ip bgp
E.show ip bgp summary
F.sh ip bgp database
A.The configuration on the FTP server is copied to RAM
B.The command is not valid on a Cisco router
C.The configuration file in RAM is copied to an FTP server
D.The configuration file in NVRAM is copied to an FTP server
E.The configuration on the FTP server is copied to NVRAM
F.The configuration will be copied from NVRAM to an FTP server with a filename of Kevin
A.00-00-0c-c0-05-0a
B.00-00-0c-cl-05-0a
C.01-00-5e-00-00-0c
D.01-00-5e-41-05-0a
E.00-00-0c-01-00-5e
F.01-00-5e-cl-05-0a
A.Memory requirements are higher for shared distribution tree than for source distribution tree
B.Creates a tree from a central RP to all last-hop routers
C.Uses a rendezvous point
D.An optimal path is created between each source router and each last-hop router
E.Place (S,G) entry in each router’s multicast routing table
F.Place (*,G) entry in a router’s multicast routing to table
A.Statically defined RP
B.Bootstrap Router
C.Auto-RP
D.RP Discovery Protocol (RDP)
E.RP Helios
F.RPARP(RARP)
A.it is not a valid NetFlow command
B.it is an SNMP command that exports 1500-byte packets to IP address 192.168.1.50
C.it is a NetFlov/ command that v/ill export 1500-byte packets to IP address 192.168.1.50
D.it is a NetFlov/ command that allows IP address 192.168.1.50 to send traffic to port 1500
E.It is a NetFlov/ command that v/ill specify that the NetFlov/ collector’s IP address is192.168.1.50 over UDP port 1500
F.It is an SNMP command that exports flows to destination address 1Q2.168.1.50 for packets upto an MTU of 1500
A.Following the traffic path
B.Top-down
C.Comparing configurations
D.Bottom-up
E.Divide and conquer
F.Examine SLAs
A.Extranet VPN
B.Managed overlay VPN topology
C.Hub-and-spoke VPN topology
D.Central-site VPN topology
E.Full mesh VPN topology
F.Remote-access VPN topology
A.The interface must be configured as a Multilink PPP interface
B.The correct bandwidth should be configured on the interface
C.A QoS policy must not be currently attached to the interface
D.CEF must be enabled
E.AutoQoS must be enabled globally before it can be enabled on the interface
F.An IP address must be configured on the interface if its speed is equal to or less than 768 kbps
A.Serial connection
B.Secure Shell
C.RADIUS
D.Simple Network Management Protocol
E.HTTP
F.Telnet
最新試題
This item contains several questions that you must answer. You can view these questions byclicking on the Questions button to the left. Changing questions can be accomplished by clicking the numbers to the left of each question. In order to complete the questions, you will need to referto the SDM and the topology, neither of which is currently visible.To gain access to either the topology or the SDK click on the button to left side of the screen thatcorresponds to the section you wish to access. When you have finished viewing the topology theSDK you can return to your questions by clicking on the Questions button to the left.Which defined peer IP address an local subnet belong to Crete?()
Which three statements accurately describe IOS Firewall configurations?()
Drag the IPsec protocol description from the above to the correct protocol type on the below.(Notall descriptions will be used)Drag and Drop question, drag each item to its proper location.
Which statement correctly describes IPsec VPN backup technology?()
Drag the correct statements about MPLS-based VPN on the left to the boxes on the right.(Not allstatements will be used)
Drag the DSL technologies on the left to their maximum(down/up) data rate values on the below.
Which statement about PPPoA configuration is correct?()
This item contains several questions that you must answer. You can view these questions byclicking on the Questions button to the left. Changing questions can be accomplished by clickingthe numbers to the left of each question. In order to complete the questions, you will need to referto the SDM and the topology, neither of which is currently visible. To gain access to either thetopology or the SDK click on the button to left side of the screen that corresponds to the sectionyou wish to access. When you have finished viewing the topology the SDK you can return to yourquestions by clicking on the Questions button to the left.Which IPSec rule is used for the Olympia branch and what does it define?()
Which two encapsulation methods require that an 827 ADSL router be configured with a PPPusername and CHAP password?()
Match the xDSL type on the above to the most appropriate implementation on the below.