A. Fibre Channel ports must be configured from the first port in the module.
B. Ethernet ports must be configured from the last port in the module.
C. Fibre Channel ports must be configured from the last port in the module.
D. Ethernet ports must be configured from the first port in the module.
您可能感興趣的試卷
你可能感興趣的試題
A. LLDP transmit and receive are disabled
B. The initiator server has no connectivity to the target storage
C. FIP negotiation timing
D. Peer does not support LLDP
E. VSAN trunk protocol has been enabled
A. Server’s CNA does not support DCBX and PFC TLV was not negotiated.
B. A "no-drop" class has not been configured for FCoE
C. The system is running with the default QOS policies.
D. The link is oversubscribed.
A. show flogi database
B. show system fc login
C. show npv flogi-table
D. show npv fcns database
E. show interface vfc X flogi
F. show interface flogi
A. Priority flow control
B. Buffer-to-buffer credits
C. TCP retransmission
D. Ethernet checksum
E. QoS policies
A. Cannot be disabled
B. Cannot have the CoS changed
C. Can have "Packet Drop" enabled
D. Is multicast optimized
E. Can have the MTU changed
A. 1
B. 2
C. 4
D. 5
E. 16
A. It’s hard-set and cannot be disabled
B. It’s configurable, with an upper limit of 16
C. It’s hard-set but cannot disable best-effort and Fibre Channel
D. It’s hard-set but can disable all but one class
E. It’s configurable with an upper limit of eight
A. LLDP
B. LACP
C. PFC
D. FIP
Which statement describes the below output from an MDS switch?()
Flow ID. 44 Initiator VSAN: 200
Initiator WWN: 50:06:04:8a:cc:19:12:db
Target VSAN: 200
Target WWN: 50:06:04:8c:de:ad:be:ef T
arget LUN: ALL LUNs Flow Verification Status:
-------------------------
Initiator Verification Status: success
Target Verification Status: WWN was not found in name server
Initiator Linecard Status: success
Target Linecard Status: Status not yet checked
Feature Status:
---------------
Write-Acceleration enabled
Write-Acceleration Buffers: 1024
Configuration Status: flow verification failed
A. The zone containing both the initiator and target does not exist
B. The zone set has not been activated
C. The target is not logged into the fabric
D. The pWWN used for the target is invalid
A. Adapter FEX is a software feature that can be configured on any CNA as long as the Nexus 5000 is running a version of code that supports Adapter FEX
B. Adapter FEX can be thought of as a way to divide a single physical link into multiple virtual links or channels.
C. Packets on each channel are tagged with an 801.Q header that has a specific source VIF
D. When using a dual-homed NIC on the server, active/standby is not supported. Only active/active is supported.
最新試題
In a Cisco Unified Computing System, What is the "designated receiver" port in end-host mode used for?()
In a Cisco Unified Computing System, where are SAN port channels connected to?()
Which three statements are possible causes for the "fltAdaptorHostIfLink-down" fault in UCS Manager? ()
From the Cisco UCS CLI, how do you verify which uplink ports a blade server is using for its network connectivity?()
Which statement is true regarding Backup tasks in Cisco UCS?()
Which two statements about end-host mode in SAN connectivity in a Cisco UCS environment are true? ()
Which are valid statements about Cisco Virtual Interface Card (VIC)? ()
KAL-AP on the Cisco ACE allows communication with Cisco ACE Global Site Selector, to report virtual IP and real server availability. Which statement is true about KAL-AP?()
Refer to the exhibit.The Cisco UCS domain is operating in switching mode. A network administrator notices that no traffic is traversing the uplinks on Fabric Interconnect B (Path C). Which actions might be used to change this behavior?()
Server load balancing (SLB) is the process of deciding to which server a load-balancing device should send a client request for service. Which predictors are supported on ACE in order to select the best server to fulfill a client request? ()