Which statement describes the below output from an MDS switch？（）
Flow ID. 44 Initiator VSAN： 200
Initiator WWN： 50：06：04：8a：cc：19：12：db
Target VSAN： 200
Target WWN： 50：06：04：8c：de：ad：be：ef T
arget LUN： ALL LUNs Flow Verification Status：
-------------------------
Initiator Verification Status： success
Target Verification Status： WWN was not found in name server
Initiator Linecard Status： success
Target Linecard Status： Status not yet checked
Feature Status：
---------------
Write-Acceleration enabled
Write-Acceleration Buffers： 1024
Configuration Status： flow verification failed
A. The zone containing both the initiator and target does not exist
B. The zone set has not been activated
C. The target is not logged into the fabric
D. The pWWN used for the target is invalid
您可能感興趣的試卷
你可能感興趣的試題
A. Adapter FEX is a software feature that can be configured on any CNA as long as the Nexus 5000 is running a version of code that supports Adapter FEX
B. Adapter FEX can be thought of as a way to divide a single physical link into multiple virtual links or channels.
C. Packets on each channel are tagged with an 801.Q header that has a specific source VIF
D. When using a dual-homed NIC on the server， active/standby is not supported. Only active/active is supported.
Refer to the exhibit.
Given this FCoE topology， host VFC interface and FC storage are in the same VSAN （VSAN 10）.The VSAN is in the allow list for both ISLs. Both ISLs are up at 4 GB.
Which command can be issued on the N5K command line to confirm that SCSI traffic from the host to the storage will flow across both links， as opposed to using only one link？（）
A. show fspf traffic vsan 10
B. show vsan 10
C. show trunk protocol
D. show fcroute unicast vsan 10
A. port security
B. fabric binding
C. IVR
D. port tracking
E. FICON
A. Two peer devices： the vPC peers of which one is primary and one is secondary and are part of a vPC domain.
B. A Layer 3 Gigabit Ethernet link called peer-keepalive link to resolve dual-active scenarios
C. A redundant 10 Gigabit Ethernet PortChannel called a peer link to carry traffic from one system to the other when needed
D. vPC member ports forming the PortChannel
E. A dot1q trunk between the vPC peers
F. A management port that can be used as peer-keepalive link to resolve dual-active scenarios.
A. The Ethanalyzer captures control-plane traffic， while SPAN captures all traffic.
B. The Ethanalyzer captures all traffic including control-plane traffic， while SPAN captures only the control-plane traffic.
C. The Ethanalyzer captures only data traffic， while SPAN captures all traffic.
D. The Ethanalyzer captures only control traffic， while SPAN captures data traffic.
A. show memory detailed
B. show process cpu sorted
C. show system resources
D. show hardware capacity
A. show interface priority-flow-control
B. show interface queuing
C. show queuing interface
D. show policy-map system type queuing
E. show policy-map interface ethernet
Nexus7000# config t
Nexus700（config）# interface ethernet 2/11
Nexus700（config-if）# switchport mode private-vlan host
Nexus700（config-if）# switchport private-vlan host-association 14 50
Nexus700（config-if）# exit
Nexus700（config）#
What will this command sequence achieve？（）
A. associate interface E2/11 to community VLANs 14 and 50
B. associate interface E2/11 to secondary VLANs 14 and 50
C. associate interface E2/11 to primary VLAN 50 and secondary VLAN 14
D. associate interface E2/11 to primary VLAN 14 and secondary VLAN 50
A. Port priority value can be configured between 1 and 65535.
B. A higher port priority value means a higher priority of LACP.
C. Port priority can be configured so that specific links can be chosen as active links rather than the hot standby links within the port channel.
D. LACP uses the port priority with the port number to form the port identifier.
E. LACP Port priority default value should always be changed
A. Cisco AV-pair
B. TACACS+ or RADIUS ack frame role attribute
C. DH-CHAP challenge attribute
D. privilege level attribute
最新試題
Which of the following are supported in Cisco Global Site Selector？ （）
Which GSS "source access list" is used to allow access to GSS by clients when GSS is being used as the DNS？（）
What is the use of an "all configuration" backup in Cisco UCS？（）
Application Control Engine （ACE） can check the health of servers and server farms by configuring health probes （which are sometimes referred to as keepalives）. A probe can be one of many types. Which are valid ACE probes？ （）
What is the appliance port used to connect to in a Cisco Unified Computing System？（）
A Cisco UCS fabric interconnect in end-host mode learns MAC addresses on which port types？（）
Which three statements are possible causes for the "fltAdaptorHostIfLink-down" fault in UCS Manager？ （）
When testing ICMP access to a functional load-balancing ACE VIP， it fails. What is the reason of this problem？ （）
What is the purpose of this command in a Cisco Application Control Engine？（） switch/Admin# show np 1 me-stats "-F0 v"
What is required for Cisco UCS C-Series rack server integration with Cisco UCS Manager？（）