A.802.1Q giants frames could saturate the link.
B.VLAN10 on CAT1 and VLAN1 on CAT2 will send untagged frames.
C.A native VLAN mismatch error message will appear.
D.VLAN10 on CAT1 and VLAN1 on CAT2 will send tagged frames.
您可能感興趣的試卷
你可能感興趣的試題
A.show configuration
B.show environment
C.show inventory
D.show platform
E.show version
A.%
B.@
C.>
D.$
E.#
A.255.255.255.0
B.255.255.255.192
C.255.255.255.250
D.255.255.255.252
A.On router R2, configure a default static route to the 192.168.1.0 network.
B.On router R2, configure DNS to resolve the URL assigned to Web Server 2 to the 192.168.1.10 address.
C.On router R1, configure NAT to translate an address on the 209.165.100.0/24 network to 192.168.1.10.
D.On router R1, configure DHCP to assign a registered IP address on the 209.165.100.0/24 network to Web Server 2.
A.0
B.1
C.2
D.3
E.4
A.ip route 0.0.0.0 0.0.0.0 s0/0/0
B.ip route 0.0.0.0 0.0.0.0 209.165.200.226
C.ip route 209.165.200.0 255.255.255.0 192.168.1.250
D.ip route 192.168.1.0 255.255.255.0 209.165.100.250
A.using adapters and access points manufactured by the same company
B.overlapping the wireless cell coverage by at least 10%
C.configuring all access points to use the same channel
D.utilizing MAC address filtering to allow the client MAC address to authenticate with the surrounding APs
A.AES-CCMP
B.PPK via IV
C.PSK
D.TKIP/MIC
A.transparent
B.auto
C.on
D.desirable
E.blocking
F.forwarding
A.Full-duplex Ethernet consists of a shared cable segment. Half-duplex Ethernet provides a point-to-point link.
B.Full-duplex Ethernet uses a loopback circuit to detect collisions. Half-duplex Ethernet uses a jam signal.
C.Full-duplex Ethernet can provide higher throughput than can half-duplex Ethernet of the same bandwidth.
D.Full-duplex Ethernet uses two wires to send and receive. Half-duplex Ethernet uses one wire to send and receive.
最新試題
A network administrator is planning a network installation for a large organization.The design requires 100 separate subnetworks,so the company has acquired a Class B network address.What subnet mask will provide the 100 subnetworks required, if 500 usable host addresses are required per subnet?()
Which command displays the CHAP authentication process as it occurs between two routers?()
A network administrator is trying to add a new router into an established OSPF network.The networks attached to the new router do not appear in the routing tables of the other OSPF routers.Given the information in the partial configuration shown below,what configuration error is causing this problem?()Router(config)#router ospf 1Router(config-router)#network 10.0.0.0 255.0.0.0 area 0
An administrator must assign static IP addresses to the servers in a network.For network 192.168.20.24/29, the router is assigned the first usable host address while the sales server is given the last usable host address. Which of the following should be entered into the IP propertied box for the sales server?()
Which Cisco IOS diagnostics command can disrupt the operation of a router under high-load conditions?()
On which options are standard access list based?()
What is the default administrative distance of OSPF?()
If all OSPF routers in a single area are configured with the same priority value,what value dose a router use for the ODPF router ID in the absence of a loopback interface?()
The network administrator cannot to switch 1 over a telnet session,although the hosts attached to switch 1 can ping the interface Fa0/0 of the router.Given the information in the graphic and assuming that the router and switch2 are configured properly,which of the following commands should be issued on switch 1 to correct this problem?()
What is the subnetwork address for a host with the IP address 201.100.5.68/28?()