A.filter-list
B.inbound ACL
C.route-map
D.outbound ACL
E.prefix-list
F.neighbor 10.0.0.1 deny-map my-map command
您可能感興趣的試卷
你可能感興趣的試題
A.configuring EIGRP stubs
B.configuring a second EIGRP AS and redistributing
C.configuring summary addresses
D.configuring an offset-list
E.configuring a prefix-list
F.configuring unicast neighbors
A.It will fragment the packet at Layer 2.
B.It will fragment the packet at Layer 3.
C.It will drop the packet and send an ICMPv6 message "packet too big" back to the source.
D.It will drop the packet.
A.ldp explicit-null
B.mpls forwarding explicit-null
C.mpls ldp advertise-labels explicit null
D.mpls ldp explicit-null
A. O IA
B. O E1
C. O E2
D. O
A.only the local OSPF routes
B.only the OSPF routes installed in the routing table
C.only the remotely learned OSPF routes
D.all the OSPF routes from the OSPF database that are eligible to be put in the routing table
A.VRF definition for IPv6
B.MP BGP for IPv6
C.LDP
D.VRF-enabled routing protocol
E.VRF-enabled interface
A.ipv6 router rip ccie distribute-list..
B.ipv6 router rip ccie offset-list..
C.interface e0/0 ipv6 rip ccie distribute-list..
D.interface e0/0 ipv6 rip ccie advertise..
A.Out-of-profile packets are queued.
B.It causes TCP retransmits.
C.Marking and remarking are not supported.
D.It does not respond to BECN and foresight messages.
E.It uses a single- and two-bucket mechanism for metering.
Refer to the exhibit. R2 and R3 are routers connected using Ethernet services from a service provider and can receive pings from each other. OSPF is configured as the routing protocol but adjacency is not happening. According to the output of the show commands in the exhibit, what could be the most likely cause of the problem? ()
A. Ethernet interfaces were configured as point-to-point.
B. Process IDs are not matching.
C. Configured bandwidths do not match on both interfaces.
D. Broadcasts and multicast are not being propagated over the Ethernet services.
E. OSPF cost does not match on both interfaces.
A.instances can control a selection of VLANs
B.load balancing
C.fast transition to forwarding state
D.backbone,uplink,and portfast (or equivalent)
E.root,loop,and BPDU guard (or equivalent)
最新試題
Which command is used to enable SSM with the range 232.0.0.0 - 255.0.0.0?()
Which two of these are used in the selection of a root bridge in a network utilizing Spanning Tree ProtocolIEEE 802.1 D?()
The classic Spanning Tree Protocol (802.1 D 1998) uses which sequence of variables to determine thebest received BPDU?()
Which three options are valid ways to filter routes from a BGP peer?()
Based on the output provided in the exhibit, to which address or location will the router forward a packet sent to 192.168.32.1?()
When STP UplinkFast is enabled on a switch utilizing the default bridge priority, what will the new bridgepriority be changed to?()
Which types of prefixes will a router running BGP most likely advertise to an IBGP peer, assuming it is notconfigured as a route reflector?()
Which three protocols or applications should be placed in a class that is configured with WRED?()
All of these are fundamental building blocks of differentiated services Traffic Conditioner Block exceptwhich one?()
In PIM-SM what control plane signaling must a multicast source perform before it begins to send multicasttraffic to a group?()