A.ipv6 router rip ccie distribute-list..
B.ipv6 router rip ccie offset-list..
C.interface e0/0 ipv6 rip ccie distribute-list..
D.interface e0/0 ipv6 rip ccie advertise..
您可能感興趣的試卷
你可能感興趣的試題
A.Out-of-profile packets are queued.
B.It causes TCP retransmits.
C.Marking and remarking are not supported.
D.It does not respond to BECN and foresight messages.
E.It uses a single- and two-bucket mechanism for metering.
Refer to the exhibit. R2 and R3 are routers connected using Ethernet services from a service provider and can receive pings from each other. OSPF is configured as the routing protocol but adjacency is not happening. According to the output of the show commands in the exhibit， what could be the most likely cause of the problem？ （）
A. Ethernet interfaces were configured as point-to-point.
B. Process IDs are not matching.
C. Configured bandwidths do not match on both interfaces.
D. Broadcasts and multicast are not being propagated over the Ethernet services.
E. OSPF cost does not match on both interfaces.
A.instances can control a selection of VLANs
B.load balancing
C.fast transition to forwarding state
D.backbone，uplink，and portfast （or equivalent）
E.root，loop，and BPDU guard （or equivalent）
A.the table of 4096 elements that map the respective VLAN to STP instance number
B.VTP version
C.configuration revision number
D.native VLAN ID
A.PIM sparse mode is being used.
B.PIM dense mode is being used.
C.The BGP multicast address family has not been configured.
D.IGMP version 3 is being used.
E.IP PIM neighbor filters have not been applied.
A.ip sla 1 icmp-echo 1.1.1.1 tos 160
B.ip sla 1 icmp-echo 1.1.1.1 tos 20
C.ip sla 1 icmp-echo 1.1.1.1 precedence 5
D.ip sla 1 icmp-echo 1.1.1.1 dscp 20
A.The phones are not sending traffic with the correct DSCP value.
B.The Cisco CallManager is not marking the traffic correctly.
C.This is most likely a bug on the CE routers.
D.Your LAN QoS is incorrectly configured.
A.routing issue
B.denial-of-service attack
C.MAC flooding
D.spanning-tree recalculation
E.Layer 2 loop
F.ARP spoofing attack
A. The switches are not the same model
B. You are not using the correct SFP
C. You are not using correct optical media converters
D. Configuration should be modified， because the distance is longer
A. Tunnel IPv6 over IPv4 to connect far-end IPv6 networks
B. Explain why configuring IPv4 and IPv6 at the same time over the same LAN interface is not possible
C. Explain why configuring IPv4 and IPv6 at the same time over the same LAN interface is possible
D. What is the meaning of EUI-64 and how does it work？
E. Tunnel IPv4 over IPv6 to connect far-end IPv4 networks.
最新試題
In PIM-SM what control plane signaling must a multicast source perform before it begins to send multicasttraffic to a group？（）
How does an IPv6 router deal with a packet that is larger than the outgoing interface MTU？（）
In order to configure two routers as anycast RPs， which of these requirements， af a minimum， must besatisfied？（）
Which command is used to enable SSM with the range 232.0.0.0 - 255.0.0.0？（）
Which two EIGRP options will limit a query domain？（）
When STP UplinkFast is enabled on a switch utilizing the default bridge priority， what will the new bridgepriority be changed to？（）
Choose two commands that are required to enable multicast on a router， when it is known that thereceivers use a specific functionality of IGMPv3.（）
All of these are fundamental building blocks of differentiated services Traffic Conditioner Block exceptwhich one？（）
Which multicast address is reserved for cisco-rp-discovery？（）
Spanning Tree Protocol IEEE 802.1 s defines the ability to deploy which of these？（）