A.It will fragment the packet at Layer 2.
B.It will fragment the packet at Layer 3.
C.It will drop the packet and send an ICMPv6 message "packet too big" back to the source.
D.It will drop the packet.
您可能感興趣的試卷
你可能感興趣的試題
A.ldp explicit-null
B.mpls forwarding explicit-null
C.mpls ldp advertise-labels explicit null
D.mpls ldp explicit-null
A. O IA
B. O E1
C. O E2
D. O
A.only the local OSPF routes
B.only the OSPF routes installed in the routing table
C.only the remotely learned OSPF routes
D.all the OSPF routes from the OSPF database that are eligible to be put in the routing table
A.VRF definition for IPv6
B.MP BGP for IPv6
C.LDP
D.VRF-enabled routing protocol
E.VRF-enabled interface
A.ipv6 router rip ccie distribute-list..
B.ipv6 router rip ccie offset-list..
C.interface e0/0 ipv6 rip ccie distribute-list..
D.interface e0/0 ipv6 rip ccie advertise..
A.Out-of-profile packets are queued.
B.It causes TCP retransmits.
C.Marking and remarking are not supported.
D.It does not respond to BECN and foresight messages.
E.It uses a single- and two-bucket mechanism for metering.
Refer to the exhibit. R2 and R3 are routers connected using Ethernet services from a service provider and can receive pings from each other. OSPF is configured as the routing protocol but adjacency is not happening. According to the output of the show commands in the exhibit， what could be the most likely cause of the problem？ （）
A. Ethernet interfaces were configured as point-to-point.
B. Process IDs are not matching.
C. Configured bandwidths do not match on both interfaces.
D. Broadcasts and multicast are not being propagated over the Ethernet services.
E. OSPF cost does not match on both interfaces.
A.instances can control a selection of VLANs
B.load balancing
C.fast transition to forwarding state
D.backbone，uplink，and portfast （or equivalent）
E.root，loop，and BPDU guard （or equivalent）
A.the table of 4096 elements that map the respective VLAN to STP instance number
B.VTP version
C.configuration revision number
D.native VLAN ID
A.PIM sparse mode is being used.
B.PIM dense mode is being used.
C.The BGP multicast address family has not been configured.
D.IGMP version 3 is being used.
E.IP PIM neighbor filters have not been applied.
最新試題
All of these are fundamental building blocks of differentiated services Traffic Conditioner Block exceptwhich one？（）
Which three message types are valid PIMv2 message types？（）
What is the command to configure RSVP to reserve up to one-tenth of a Gigabit link，but only allow eachindividual flow to use 1 MB/s？（）
Which command is used to enable SSM with the range 232.0.0.0 - 255.0.0.0？（）
Which of these statements about penultimate hop popping are true？（）
In GLBP，which router will answer on client ARP requests？（）
When STP UplinkFast is enabled on a switch utilizing the default bridge priority， what will the new bridgepriority be changed to？（）
How does an IPv6 router deal with a packet that is larger than the outgoing interface MTU？（）
On the basis of the network provided in the exhibit， all routers are configured to run EIGRP on all links. If the link between PG-R1 and PG-R2 fails， what is the maximum number of queries PG-R3 will receive for 192.168.1.0/24， assuming that all the packets sent during convergence are transmitted once （there are no dropped or retransmitted packets）？（）
You are the network administrator of an enterprise with a main site and multiple remote sites. Your networkcarries both VOIP and data traffic. You agree with your service provider to classify VOIP and data trafficaccording to the different service RFCs. How can your data and VOIP traffic be marked？（）