VLANs have been enabled on an autonomous access point.
In order for clients associating toVLANs other than the native VLAN to receive an IP address which of the following must beconfigured？（）
A.access point Ethernet port set to SSL trunking
B.switchport set to 802.1q trunking
C.switchport set to SSL trunking
D.access point Ethernet port not set to 802.1q trunking
您可能感興趣的試卷
你可能感興趣的試題
A.router（config）# wlccp authentication-server infrastructure eap Group_1
B.router（config）# wlccp authentication-server infrastructure eap-fast Group_1
C.router（config）# wlccp authentication-server client eap-fast Group_1
D.router（config）# wlccp authentication-server client eap Group_1
A.registration error
B.authentication failures threshold
C.HTTP disabled
D.Telnet disabled
A.802.1q trunking
B.VTP trunking
C.ISL trunking
D.DPT trunking
There are 30 managed access points on the WLSE. A radio scan is started but fails. Upon inspection of the device list in the reports tab， you notice a red indicator on the WDS access point.Upon inspection of the WDS access point through its GUI， it is discovered that the security keys arenot set up between the WDS access point and the WLSE.
Which of the following is misconfigured？（）
A.SNMP communities
B.Telnet/SSH user/password
C.WLCCP credentials
D.HTTP user/password
You are using ADU and are authenticated and associated to an access point. You are unable toobtain an IP address.
Which of the following will cause this problem？（）
A.AES encryption enabled
B.TKIP enabled
C.third-party wireless supplicant enabled
D.802.1X authentication type enabled
On a Series 1010 lightweight access point， the alarm LED is flashing red， and all other LEDs are off.
What is the lightweight access point indicating？（）
A.It has lost contact with controller.
B.Its IP address already exists.
C.It requires a code upgrade.
D.It is operating normally.
A.router# show wlccp ap
B.router# show wlccp wds ap
C.router# show wlccp cckm
D.router# show wlccp wds cckm
A.HTTPS
B.TFTP
C.RMI
D.HTTP
E.FTP
A.SSIDs are not case sensitive.
B.SSIDs must be listed in the same order in the ADU as they are in the access point.
C.A maximum of three SSIDs may be configured.
D.SSIDs may have a maximum of 16 characters.
Using the WLSE，you are trying to push out a configuration job to an access point，but the job doesnot start.
Which of the following would cause this failure？（）
A.invalid parameter in the template
B.incorrect SNMP communities on the access point
C.unsupported version of IOS firmware in the access point
D.pop-up blocker enabled in the browser
最新試題
You are installing a Cisco 4402 Series Wireless LAN Controller.What type of interface is used on the uplink port？（）
An REAP was supporting 16 WLANs， but now it only supports one.What happened to cause the change？（）
You are installing a Cisco Aironet 1000 Series controller-based access point. When you boot it， allthe LEDs on the access point blink together.What does this indicate about the access point？（）
A client roams from H-REAP AP1 to H-REAP AP2. The client is unable to associate to H-REAP AP2.H-REAP AP2 has six other clients associated to it， which continue to pass traffic.What has causedthis problem？（）
You are configuring an RF group of controllers that coordinate Radio Resource Management calculations.What is the maximum number of WLAN controllers that you can add？（）
You are using ADU and are authenticated and associated to an access point. However， you are unable to obtain an IP address.Which of these has caused this problem？（）
On a WLAN controller， what is the default roaming bandwidth percentage reserved for voice clients？（）
You are charges with implementing a secure wireless installation which will provide Internet accessto client devices but will not allow communications between wireless clients.In addition to implementing PSPF or peer-to-peer blocking on the wireless side，which of the following actionsshould you perform on the wired infrastructure？（）
Which of the following commands on the wireless interface of a Cisco 3845 Integrated Service Router allows the SSID to broadcast？（）
Static WEP is configured on the access point. You are authenticated and associated to the accesspoint but are unable to obtain an IP address.Which of the following will cause this problem？（）