A.802.1q trunking
B.VTP trunking
C.ISL trunking
D.DPT trunking
您可能感興趣的試卷
你可能感興趣的試題
There are 30 managed access points on the WLSE. A radio scan is started but fails. Upon inspection of the device list in the reports tab, you notice a red indicator on the WDS access point.Upon inspection of the WDS access point through its GUI, it is discovered that the security keys arenot set up between the WDS access point and the WLSE.
Which of the following is misconfigured?()
A.SNMP communities
B.Telnet/SSH user/password
C.WLCCP credentials
D.HTTP user/password
You are using ADU and are authenticated and associated to an access point. You are unable toobtain an IP address.
Which of the following will cause this problem?()
A.AES encryption enabled
B.TKIP enabled
C.third-party wireless supplicant enabled
D.802.1X authentication type enabled
On a Series 1010 lightweight access point, the alarm LED is flashing red, and all other LEDs are off.
What is the lightweight access point indicating?()
A.It has lost contact with controller.
B.Its IP address already exists.
C.It requires a code upgrade.
D.It is operating normally.
A.router# show wlccp ap
B.router# show wlccp wds ap
C.router# show wlccp cckm
D.router# show wlccp wds cckm
A.HTTPS
B.TFTP
C.RMI
D.HTTP
E.FTP
A.SSIDs are not case sensitive.
B.SSIDs must be listed in the same order in the ADU as they are in the access point.
C.A maximum of three SSIDs may be configured.
D.SSIDs may have a maximum of 16 characters.
Using the WLSE,you are trying to push out a configuration job to an access point,but the job doesnot start.
Which of the following would cause this failure?()
A.invalid parameter in the template
B.incorrect SNMP communities on the access point
C.unsupported version of IOS firmware in the access point
D.pop-up blocker enabled in the browser
A.75
B.100
C.25
D.50
Client association using EAP-Cisco Wireless (LEAP) is failing, but EAP-PEAP is functioning on an autonomous access point.
Which of the following needs to be enabled on the access point so EAP-Cisco Wireless (LEAP) is enabled?()
A.open authentication plus MAC
B.open authentication plus EAP
C.shared key
D.network EAP
A.Devices
B.IDS
C.Configure
D.Reports
最新試題
You want to dynamically assign users to an 802.1Q VLAN as a result of their authentication. Inorder to accomplish this.Which two IETF RADIUS attributes should you configure on the CiscoSecure ACS? ()
You are troubleshooting a problem with a Cisco 7920 wireless IP phone that is causing the phoneto drop calls. The problem appears to be roaming bandwidth issue. In order to verify what kind ofissue it is, you decide to increase the bandwidth reserve for roaming on the WLAN controller tomaximum.What level do you set the bandwidth to?()
Which protocol does the RADIUS server use inside the secure tunnel of EAP-FAST to authenticatethe client when one-time passwords are in use?()
You are installing a Cisco 4402 Series Wireless LAN Controller.What type of interface is used on the uplink port?()
You are configuring an RF group of controllers that coordinate Radio Resource Management calculations.What is the maximum number of WLAN controllers that you can add?()
If it is properly deployed, a controller-based access point is capable of monitoring all VLANs on anetwork when you select which of the following modes from the AP Mode drop-down menu onthe controller?()
A mobility group is created by a Cisco WLCM and 4402 Series Wireless LAN Controller. A client thatis anchored on the Cisco WLCM roams to an access point on the 4402 controller. You then run adebug command on the 4402 controller.Which message would best describe the establishment ofthe tunnel from the foreign controller’s perspective?()
Which of the following parameter sets must be configured on the Cisco Wireless Location Appliance?()
The IOS of a North American Cisco Aironet 1130AG Series standalone access point has becomecorrupt. You must therefore reload the TFTP firmware.Before you press and hold the MODEbutton, you should verify that the file name is which of the following?()
On a Cisco Aironet 1240AG Series standalone access point, the radio LED is dark blue and blinking,but the status LED and Ethernet LED are both off.What does this indicate?()