There are 30 managed access points on the WLSE. A radio scan is started but fails. Upon inspection of the device list in the reports tab, you notice a red indicator on the WDS access point.Upon inspection of the WDS access point through its GUI, it is discovered that the security keys arenot set up between the WDS access point and the WLSE.
Which of the following is misconfigured?()
A.SNMP communities
B.Telnet/SSH user/password
C.WLCCP credentials
D.HTTP user/password
您可能感興趣的試卷
你可能感興趣的試題
You are using ADU and are authenticated and associated to an access point. You are unable toobtain an IP address.
Which of the following will cause this problem?()
A.AES encryption enabled
B.TKIP enabled
C.third-party wireless supplicant enabled
D.802.1X authentication type enabled
On a Series 1010 lightweight access point, the alarm LED is flashing red, and all other LEDs are off.
What is the lightweight access point indicating?()
A.It has lost contact with controller.
B.Its IP address already exists.
C.It requires a code upgrade.
D.It is operating normally.
A.router# show wlccp ap
B.router# show wlccp wds ap
C.router# show wlccp cckm
D.router# show wlccp wds cckm
A.HTTPS
B.TFTP
C.RMI
D.HTTP
E.FTP
A.SSIDs are not case sensitive.
B.SSIDs must be listed in the same order in the ADU as they are in the access point.
C.A maximum of three SSIDs may be configured.
D.SSIDs may have a maximum of 16 characters.
Using the WLSE,you are trying to push out a configuration job to an access point,but the job doesnot start.
Which of the following would cause this failure?()
A.invalid parameter in the template
B.incorrect SNMP communities on the access point
C.unsupported version of IOS firmware in the access point
D.pop-up blocker enabled in the browser
A.75
B.100
C.25
D.50
Client association using EAP-Cisco Wireless (LEAP) is failing, but EAP-PEAP is functioning on an autonomous access point.
Which of the following needs to be enabled on the access point so EAP-Cisco Wireless (LEAP) is enabled?()
A.open authentication plus MAC
B.open authentication plus EAP
C.shared key
D.network EAP
A.Devices
B.IDS
C.Configure
D.Reports
A.1813
B.1645
C.1646
D.1812
最新試題
Static WEP is configured on the access point. You are authenticated and associated to the accesspoint but are unable to obtain an IP address.Which of the following will cause this problem?()
Which of the following parameter sets must be configured on the Cisco Wireless Location Appliance?()
You review the Failed Attempts logs on an AAA server and find: "unknown network access servererror." Which failure could produce this error?()
What is the maximum number of wireless controllers that the highest-end Cisco WCS server canmanage?()
Which of the following accurately represents the functionality of a lightweight access point configured to operate in sniffer AP mode?()
You are trying to change the polling parameters used by the location manager via the Cisco WCS,and your request is being denied. What is wrong?()
You are troubleshooting a problem with a Cisco 7920 wireless IP phone on a standalone WLAN.The phone rings but, when you answer, the call is dropped.What may cause this problem?()
An REAP was supporting 16 WLANs, but now it only supports one.What happened to cause the change?()
The Cisco Wireless Location Appliance provides an audit trail for each device tracked for up to how many days?()
You are troubleshooting a one-way call problem with a Cisco 7920 wireless IP phone on a standalone WLAN.What may cause this problem?()