A Cisco WCS version 4.0 has been installed on a server with a dual Pentium 3.0 GHz processor, 4GB RAM, and an 80 GB hard drive. A location appliance has been incorporated into the network and isbeing monitored by the Cisco WCS. There are 3000 devices to be tracked but not all of them are beingtracked on the Cisco WCS.
What can be done to correct the problem?()
A.Add a new location appliance.
B.Add a new Cisco WCS server dedicated to the location appliance.
C.Add 4 GB of RAM to the Cisco WCS.
D.Add a 120 GB hard drive to the Cisco WCS.
您可能感興趣的試卷
你可能感興趣的試題
You are troubleshooting a problem with a Cisco 7920 wireless IP phone that is causing the phoneto drop calls. The problem appears to be a roaming bandwidth issue. In order to verify what kindof issue it is, you decide to increase the bandwidth reserved for roaming on the WLAN controllerto the maximum.
What level do you set the bandwidth to?()
A.25 percent
B.15 percent
C.5 percent
D.35 percent
Using the WLSE, you are trying to push out a configuration job to a standalone access point, butthe job does not start.
Which of the following would cause this failure?()
A.invalid parameter in the template
B.incorrect SNMP communities on the access point
C.pop-up blocker enabled in the browser
D.unsupported version of IOS firmware in the access point
A.50
B.128
C.512
D.1024
You are using ADU and are authenticated and associated to an access point. However, you areunable to obtain an IP address.
Which of these has caused this problem?()
A.invalid SSID
B.invalid WEP key
C.invalid encryption type
D.invalid 802.1X authentication type
A.network connections
B.location views
C.access points
D.object definitions
You have been called upon to add location-based services into an existing controller-based
wireless design which primarily encompasses handheld devices such as barcode scanners and Cisco7920 wireless IP phones.
In which mode should you deploy the additional access points to achievethe density required without excessive co-channel interference?()
A.tracking mode
B.monitor mode
C.location mode
D.sniffer mode
A Cisco Aironet 1020 controller-based access point has been connected to a Catalyst 3550-24 PWRSwitch. However, when it is powered up, the access point fails.
What has caused this problem?()
A.access point does not support 802.11h
B.incorrect switch power supply
C.switch port is not enabled
D.switch does not support 802.3af
E.access point has not been initialized with the primary controller
A.Acceptance Test Plan
B.Change Management
C.Incident Management
D.Configuration Management
A.Ongoing Support Handoff Meeting
B.Staff Training
C.Detailed Design Development
D.Staging and System Migration
最新試題
On a Cisco Aironet 802.11 a/b/g wireless LAN client adapter,the status LED and activity LED are alternating on and off.What does this indicate?()
You want to dynamically assign users to an 802.1Q VLAN as a result of their authentication. Inorder to accomplish this.Which two IETF RADIUS attributes should you configure on the CiscoSecure ACS? ()
You are troubleshooting a problem with a Cisco 7920 wireless IP phone that is causing the phoneto drop calls. The problem appears to be roaming bandwidth issue. In order to verify what kind ofissue it is, you decide to increase the bandwidth reserve for roaming on the WLAN controller tomaximum.What level do you set the bandwidth to?()
You have just finished aligning a Cisco Aironet 1400 Series Wireless Bridge link using installationmode. When you set the link back to operational mode you loose association to the root bridge.Which action will correct the problem?()
On a Cisco Aironet 1240AG Series standalone access point, the radio LED is dark blue and blinking,but the status LED and Ethernet LED are both off.What does this indicate?()
On a WLAN controller, what is the default roaming bandwidth percentage reserved for voice clients?()
If it is properly deployed, a controller-based access point is capable of monitoring all VLANs on anetwork when you select which of the following modes from the AP Mode drop-down menu onthe controller?()
How many WLANs can a Cisco Aironet 1242 in H-REAP mode support when actively connected toa wireless controller?()
You are troubleshooting a one-way call problem with a Cisco 7920 wireless IP phone on a standalone WLAN.What may cause this problem?()
You are installing a Cisco 4402 Series Wireless LAN Controller.What type of interface is used on the uplink port?()