You are using ADU and are authenticated and associated to an access point. However， you areunable to obtain an IP address.
Which of these has caused this problem？（）
A.invalid SSID
B.invalid WEP key
C.invalid encryption type
D.invalid 802.1X authentication type
您可能感興趣的試卷
你可能感興趣的試題
A.network connections
B.location views
C.access points
D.object definitions
You have been called upon to add location-based services into an existing controller-based
wireless design which primarily encompasses handheld devices such as barcode scanners and Cisco7920 wireless IP phones.
In which mode should you deploy the additional access points to achievethe density required without excessive co-channel interference？（）
A.tracking mode
B.monitor mode
C.location mode
D.sniffer mode
A Cisco Aironet 1020 controller-based access point has been connected to a Catalyst 3550-24 PWRSwitch. However， when it is powered up， the access point fails.
What has caused this problem？（）
A.access point does not support 802.11h
B.incorrect switch power supply
C.switch port is not enabled
D.switch does not support 802.3af
E.access point has not been initialized with the primary controller
A.Acceptance Test Plan
B.Change Management
C.Incident Management
D.Configuration Management
A.Ongoing Support Handoff Meeting
B.Staff Training
C.Detailed Design Development
D.Staging and System Migration
On a standalone access point， client association using EAP-Cisco Wireless （Cisco-LEAP） is failing，but association using EAP-PEAP is functioning.
What needs to be enabled on the standalone accesspoint to correct this issue？（）
A.network EAP
B.open authentication plus MAC
C.open authentication plus EAP
D.a shared key
You have just finished aligning a Cisco Aironet 1400 Series Wireless Bridge link using installationmode.When you set the link back to operational mode you loose association to the root bridge.
Which action will correct the problem？（）
A.Configure the bridge to force infrastructure devices to associate only to the SSID parameter.
B.Enable passwords on both bridges.
C.Configure the distance parameter value.
D.Configure the proper channel.
You are troubleshooting a one-way call problem with a Cisco 7920 wireless IP phone on a standalone WLAN.
What may have caused this problem？（）
A.The minimum data rate is not set to 11 Mbps.
B.Publicly Secure Packet forwarding is enabled.
C.The access point is set to the least congested channel.
D.An address resolution protocol has been disabled.
On a Cisco Aironet 1130AG Series standalone access point， the status LED is dark blue and blinking.
What does this indicate？（）
A.The internal radio has failed.
B.A firmware upgrade is in progress.
C.An access point buffer overflow is occurring.
D.The access point is booting.
最新試題
You have a very few Cisco 7920 wireless IP phones on your network， but lots of wireless laptops.You want to increase the bandwidth available for the laptops by decreasing the bandwidth reserved for the Cisco 7920 phones.What is the lowest percentage of voice-allocated bandwidthyou can select on the WLAN controller？（）
How many WLANs can a Cisco Aironet 1242 in H-REAP mode support when actively connected toa wireless controller？（）
If it is properly deployed， a controller-based access point is capable of monitoring all VLANs on anetwork when you select which of the following modes from the AP Mode drop-down menu onthe controller？（）
You are troubleshooting a one-way call problem with a Cisco 7920 wireless IP phone on a standalone WLAN.What may cause this problem？（）
Which of the following commands on the wireless interface of a Cisco 3845 Integrated Service Router allows the SSID to broadcast？（）
A mobility group is created by a Cisco WLCM and 4402 Series Wireless LAN Controller. A client thatis anchored on the Cisco WLCM roams to an access point on the 4402 controller. You then run adebug command on the 4402 controller.Which message would best describe the establishment ofthe tunnel from the foreign controller’s perspective？（）
You are installing a Cisco 4402 Series Wireless LAN Controller.What type of interface is used on the uplink port？（）
What is the maximum number of wireless controllers that the highest-end Cisco WCS server canmanage？（）
On a Cisco Aironet 802.11 a/b/g wireless LAN client adapter，the status LED and activity LED are alternating on and off.What does this indicate？（）
You want to dynamically assign users to an 802.1Q VLAN as a result of their authentication. Inorder to accomplish this.Which two IETF RADIUS attributes should you configure on the CiscoSecure ACS？ （）