A.Incident Management
B.Change Management
C.Configuration Management
D.Acceptance Test Plan
您可能感興趣的試卷
你可能感興趣的試題
A.System Monitoring
B.Security Administration
C.Operations Setup
D.Problem Management
A.Systems Integration
B.Systems Acceptance Testing
C.Skill Assessment
D.Project Close Out
E.Wireless Check
A.Maximize the number of services required to support advanced technologies.
B.Provide a consistent，repeatable，and proven method to ensure the network solution that is deployed delivers upon the customer’s goals for reliability and availability.
C.Reinforce customer confidence in partners selling products.
D.More clearly define the roles of account managers，systems engineers，and field engineers.
E.Create a more effective sales strategy for partners.
Using the WLSE， you are trying to push out a configuration job to a standalone access point， but the jobdoes not start.
Which of the following would cause this failure？（）
A.invalid parameter in the template
B.pop-up blocker enabled in the browser
C.incorrect SNMP communities on the access point
D.unsupported version of IOS firmware in the access point
You are charged with implementing a secure wireless installation which will provide Internet access to clientdevices but will not allow communications between wireless clients. In addition to implementing PSPF orpeer-to-peer blocking on the wireless side.
Which of the following actions should you perform on the wiredinfrastructure？（）
A.Take no action， you have achieved your goal.
B.Implement a Cisco Secure IPS sensor.
C.Implement a protected port on the access switches.
D.Implement 802.1X on the switch ports.
A Cisco 4404 WLAN controller is being connected to a Cisco 6500 Catalyst Series Switch.
How would younterconnect and configure LAG for connectivity and ensure redundancy？（）
A.All four ports from the Cisco WLC terminated to the same Catalyst gigabit module and channel group.
B.All four ports from the Cisco WLC terminated to the same Catalyst gigabit module using two channel groups.
C.Ports 1 and 2 from Cisco WLC to Catalyst gigabit module slot 1 channel group 20 and Cisco WLC ports3 and 4 to Catalyst gigabit module slot 2 channel group 40.
D.Ports 1 and 2 from Cisco WLC to Catalyst gigabit module slot 1 channel group 10 and Cisco WLC ports3 and 4 to Catalyst gigabit module slot 2 channel group 10.
A mobility group is created by a Cisco WLCM and 4402 Series Wireless LAN Controller. A client that isanchored on the Cisco WLCM roams to an access point on the 4402 controller. You then run a debug command on the 4402 controller.
Which message would best describe the establishment of the tunnel fromthe foreign controller’s perspective？（）
A.Transmit Mobile Anchor Export message
B.Received Mobile Anchor Export message
C.Transmit Plumbing duplex mobility tunnel message
D.Received Plumbing duplex mobility tunnel message
You want to dynamically assign users to an 802.1Q VLAN as a result of their authentication.
In order toaccomplish this，which two IETF RADIUS attributes should you configure on the Cisco Secure ACS？（）
A.064 Tunnel-Type
B.066 Tunnel-Client-Endpoint
C.067 Tunnel-Server-Endpoint
D.081 Tunnel-Private-Group-ID
E.082 Tunnel-Assignment-ID
You have been called upon to add location-based services into an existing controller-based wireless designwhich primarily encompasses handheld devices such as barcode scanners and Cisco 7920 wireless IPphones.
In which mode should you deploy the additional access points to achieve the density required without excessive co-channel interference？（）
A.sniffer mode
B.monitor mode
C.location mode
D.tracking mode
A.Monitor
B.Rogue Detector
C.Sniffer
D.Mirror
最新試題
If it is properly deployed， a controller-based access point is capable of monitoring all VLANs on anetwork when you select which of the following modes from the AP Mode drop-down menu onthe controller？（）
Which protocol does the RADIUS server use inside the secure tunnel of EAP-FAST to authenticatethe client when one-time passwords are in use？（）
When configuring a WLAN controller for a voice application using Cisco 7920 wireless IP phones，which two general control settings should you select？（）
On a Cisco Aironet 802.11 a/b/g wireless LAN client adapter，the status LED and activity LED are alternating on and off.What does this indicate？（）
You have just finished aligning a Cisco Aironet 1400 Series Wireless Bridge link using installationmode. When you set the link back to operational mode you loose association to the root bridge.Which action will correct the problem？（）
Clients using Cisco-LEAP and EAP-FAST authentication are having no problems logging on to thewireless network， but clients using PEAP are failing to log on.Which situation would result in thistype of problem？（）
A mobility group is created by a Cisco WLCM and 4402 Series Wireless LAN Controller. A client thatis anchored on the Cisco WLCM roams to an access point on the 4402 controller. You then run adebug command on the 4402 controller.Which message would best describe the establishment ofthe tunnel from the foreign controller’s perspective？（）
When configuring Cisco Secure ACS to support wireless EAP authentication， which device must be configured as a AAA client？（）
You review the Failed Attempts logs on an AAA server and find： "unknown network access servererror." Which failure could produce this error？（）
You are troubleshooting a problem with a Cisco 7920 wireless IP phone on a standalone WLAN.The phone rings but， when you answer， the call is dropped.What may cause this problem？（）