A mobility group is created by a Cisco WLCM and 4402 Series Wireless LAN Controller. A client that isanchored on the Cisco WLCM roams to an access point on the 4402 controller. You then run a debug command on the 4402 controller.
Which message would best describe the establishment of the tunnel fromthe foreign controller’s perspective?()
A.Transmit Mobile Anchor Export message
B.Received Mobile Anchor Export message
C.Transmit Plumbing duplex mobility tunnel message
D.Received Plumbing duplex mobility tunnel message
您可能感興趣的試卷
你可能感興趣的試題
You want to dynamically assign users to an 802.1Q VLAN as a result of their authentication.
In order toaccomplish this,which two IETF RADIUS attributes should you configure on the Cisco Secure ACS?()
A.064 Tunnel-Type
B.066 Tunnel-Client-Endpoint
C.067 Tunnel-Server-Endpoint
D.081 Tunnel-Private-Group-ID
E.082 Tunnel-Assignment-ID
You have been called upon to add location-based services into an existing controller-based wireless designwhich primarily encompasses handheld devices such as barcode scanners and Cisco 7920 wireless IPphones.
In which mode should you deploy the additional access points to achieve the density required without excessive co-channel interference?()
A.sniffer mode
B.monitor mode
C.location mode
D.tracking mode
A.Monitor
B.Rogue Detector
C.Sniffer
D.Mirror
A.RTS threshold = 4000, CWmin = 3
B.RTS threshold = 1, CWmin = 4
C.RTS threshold = 4000, CWmin = 5
D.RTS threshold = 1, CWmin = 5
You are configuring an RF group of controllers that coordinate Radio Resource Management calculations.
What is the maximum number of WLAN controllers that you can add?()
A.12
B.17
C.20
D.24
A.QoS Element for Wireless Phones
B.IGMP Snooping
C.WMM
D.AVVID Priority Mapping
A Cisco WCS version 4.0 has been installed on a server with a dual Pentium 3.0 GHz processor, 4 GBRAM, and an 80 GB hard drive. A location appliance has been incorporated into the network and is beingmonitored by the Cisco WCS. There are 3000 devices to be tracked but not all of them are being trackedon the Cisco WCS.
What can be done to correct the problem?()
A.Add 4 GB of RAM to the Cisco WCS.
B.Add a 120 GB hard drive to the Cisco WCS.
C.Add a new location appliance.
D.Add a new Cisco WCS server dedicated to the location appliance.
You are troubleshooting a problem with a Cisco 7920 wireless IP phone on a standalone WLAN. The phonerings but, when you answer, the call is dropped.
What may have caused this problem?()
A.The minimum data rate is not set to 11 Mbps.
B.An address resolution protocol is enabled.
C.Publicly Secure Packet forwarding is enabled.
D.The access point is set to the least congested channel.
You are troubleshooting a one-way call problem with a Cisco 7920 wireless IP phone on a standaloneWLAN.
What may have caused this problem?()
A.The minimum data rate is not set to 11 Mbps.
B.An address resolution protocol has been disabled.
C.Publicly Secure Packet forwarding is enabled.
D.The access point is set to the least congested channel.
最新試題
On a WLAN controller, what is the default roaming bandwidth percentage reserved for voice clients?()
Clients using Cisco-LEAP and EAP-FAST authentication are having no problems logging on to thewireless network, but clients using PEAP are failing to log on.Which situation would result in thistype of problem?()
You are configuring an RF group of controllers that coordinate Radio Resource Management calculations.What is the maximum number of WLAN controllers that you can add?()
The Cisco Wireless Location Appliance provides an audit trail for each device tracked for up to how many days?()
When configuring Cisco Secure ACS to support wireless EAP authentication, which device must be configured as a AAA client?()
You are installing a Cisco Aironet 1000 Series controller-based access point. When you boot it, allthe LEDs on the access point blink together.What does this indicate about the access point?()
You have been called upon to add location-based services into an existing controller-basedwireless design which primarily encompasses handheld devices such as barcode scanners and Cisco7920 wireless IP phones.In which mode should you deploy the additional access points to achievethe density required without excessive co-channel interference?()
You are using ADU and are authenticated and associated to an access point. However, you are unable to obtain an IP address.Which of these has caused this problem?()
You are troubleshooting a problem with a Cisco 7920 wireless IP phone on a standalone WLAN.The phone rings but, when you answer, the call is dropped.What may cause this problem?()
On a Cisco Aironet 1240AG Series standalone access point, the radio LED is dark blue and blinking,but the status LED and Ethernet LED are both off.What does this indicate?()