When configuring a WLAN controller for a voice application using Cisco 7920 wireless IP phones.
Whichtwo general control settings should you select?()
A.Multicast on
B.Aggressive Load Balancing off
C.Multicast off
D.AP Fallback on
E.Aggressive Load Balancing on
您可能感興趣的試卷
你可能感興趣的試題
You are installing a Cisco 4402 Series Wireless LAN Controller.
Which type of interface shouldyou use on the controller’s distribution port?()
A.1000BASE-SX SFP
B.10/100/1000 Mbps RJ45
C.10/100 Mbps RJ45
D.10000BASE-SX
By default, on the WLAN controller for a voice application using Cisco 7921 wireless IP phones.
What is the percentage of RF bandwidth that can be dedicated to the phones?()
A.75 percent
B.85 percent
C.56 percent
D.55 percent
A.Clients connected to the rogue access point must be able to connect to the containmentcontroller-based access point.
B.Multiple controller-based access points will load-balance the containment task using fewerresourcesthan a single access point.
C.Clients connected to the rogue access point may be out of the range of the controller-basedaccess point providing containment.
D.Each controller-based access point can handle only a limited amount of clients connected tothe rogue access points.
The IOS of a North American Cisco Aironet 1130AG Series standalone access point has becomecorrupt. You must therefore reload the TFTP firmware.
Before you press and hold the MODEbutton,you should verify that the file name is which of the following? ()
A.c1130-k9w7-tar.boot
B.c1130-k9w7-tar.123-7.JA1.tar
C.c1130-k9w7-tar.default
D.c1130-k9w7-tar.recover
A.Problem Management
B.Configuration Management
C.Incident Management
D.Change Management
A.15
B.10
C.1
D.5
A mobility group is created by a Cisco WLCM and 4402 Series Wireless LAN Controller. A clientthat is anchored on the Cisco WLCM roams to an access point on the 4402 controller. You then run adebug command on the 4402 controller.
Which message would best describe the establishment of the tunnel from the foreign controller’sperspective?()
A.Received Mobile Anchor Export message
B.Transmit Plumbing duplex mobility tunnel message
C.Received Plumbing duplex mobility tunnel message
D.Transmit Mobile Anchor Export message
You are charged with implementing a secure wireless installation which will provide Internet
access to client devices but will not allow communications between wireless clients. In addition toimplementing PSPF or peer-to-peer blocking on the wireless side.
Which of the following actionsshould you perform on the wired infrastructure?()
A.Implement a Cisco Secure IPS sensor.
B.Implement 802.1X on the switch ports.
C.Take no action, you have achieved your goal.
D.Implement a protected port on the access switches.
You want to dynamically assign users to an 802.1Q VLAN as a result of their authentication. Inorder to accomplish this.
Which two IETF RADIUS attributes should you configure on the Cisco SecureACS?()
A.083 Tunnel-Preference
B.066 Tunnel-Client-Endpoint
C.064 Tunnel-Type
D.082 Tunnel-Assignment-ID
E.081 Tunnel-Private-Group-ID
F.067 Tunnel-Server-Endpoint
On a Cisco Aironet 1240AG Series standalone access point, the radio LED is dark blue andblinking,but the status LED and Ethernet LED are both off.
What does this indicate()?
A.A firmware upgrade is in progress.
B.An access point buffer overflow is occurring.
C.The access point is booting.
D.The internal radio has failed.
最新試題
A mobility group is created by a Cisco WLCM and 4402 Series Wireless LAN Controller. A client thatis anchored on the Cisco WLCM roams to an access point on the 4402 controller. You then run adebug command on the 4402 controller.Which message would best describe the establishment ofthe tunnel from the foreign controller’s perspective?()
A client roams from H-REAP AP1 to H-REAP AP2. The client is unable to associate to H-REAP AP2.H-REAP AP2 has six other clients associated to it, which continue to pass traffic.What has causedthis problem?()
An REAP was supporting 16 WLANs, but now it only supports one.What happened to cause the change?()
Which of the following accurately represents the functionality of a lightweight access point configured to operate in sniffer AP mode?()
When configuring a WLAN controller for a voice application using Cisco 7920 wireless IP phones,which two general control settings should you select?()
Which of the following parameter sets must be configured on the Cisco Wireless Location Appliance?()
You are troubleshooting a one-way call problem with a Cisco 7920 wireless IP phone on a standalone WLAN.What may cause this problem?()
You are configuring a wireless LAN controller for QoS.Which 802.11e user priority tag should you apply to voice applications?()
Static WEP is configured on the access point. You are authenticated and associated to the accesspoint but are unable to obtain an IP address.Which of the following will cause this problem?()
If it is properly deployed, a controller-based access point is capable of monitoring all VLANs on anetwork when you select which of the following modes from the AP Mode drop-down menu onthe controller?()