On a Cisco Aironet 1240AG Series standalone access point, the radio LED is dark blue andblinking,but the status LED and Ethernet LED are both off.
What does this indicate()?
A.A firmware upgrade is in progress.
B.An access point buffer overflow is occurring.
C.The access point is booting.
D.The internal radio has failed.
您可能感興趣的試卷
你可能感興趣的試題
A.router(config-ssid)# enable
B.router(config-ssid)# advertise
C.router(config-ssid)# broadcast
D.router(config-ssid)# guest-mode
A.cisco aironet 1500 series
B.cisco aironet 1400 series
C.cisco aironet 1300 series
D.cisco aironet 1200 series
You review the failed attempts logs on an aaa server and find: "unknown network access server error."
Which failure could produce this error?()
A.failure of the wireless client and aaa server handshake
B.supplicant authentication failure
C.aaa client and aaa server handshake
D.wrong password used by the supplicant
You are troubleshooting a problem with a cisco 7920 wireless ip phone that is causing the phone to drop calls. the problem appears to be roaming bandwidth issuE. in order to verify what kind of issue it is, you decide to increase the bandwidth reserve for roaming on the wlan controller to maximum.
What level do you set the bandwidth to?()
A.5 percent
B.15 percent
C.25 percent
D.35 percent
A.back up the database, stop the wcs, upgrade the wcs, restore the database, start the wcs
B.stop the wcs, back up the database, upgrade the wcs, restore the database, start the wcs
C.back up the database, stop the wcs, upgrade the wcs, start the wcs, restore the database
D.stop the wcs, back up the database, upgrade the wcs, start the wcs, restore the database
When optimizing a standalone point-to-multipoint bridge installation with eight non-root bridges.
Which of the following rts threshold and cwmin settings would be correct for the non-root bridges?()
A.rts threshold=4000,cwmin=3
B.rts threshold=1,cwmin=4
C.rts threshold=4000,cwmin=5
D.rts threshold=1,cwmin=5
A.debug dhcp enable
B.debug dhcp status enable
C.debug dhcp packet enable
D.enable debug dhcp packet
You are troubleshooting a one-way call problem with a cisco 7920 wireless ip phone on a standalone wlan.
What may cause this problem?()
A.the minimum data rate is not set to 11 mbps.
B.an address resolution protocol has been disabled
C.publicly secure packet forwarding is enabled
D.the access point is set to the least congested channel.
A.35
B.50
C.100
D.250
A.7
B.60
C.14
D.30
最新試題
You are configuring an RF group of controllers that coordinate Radio Resource Management calculations.What is the maximum number of WLAN controllers that you can add?()
You are troubleshooting a one-way call problem with a Cisco 7920 wireless IP phone on a standalone WLAN.What may cause this problem?()
A mobility group is created by a Cisco WLCM and 4402 Series Wireless LAN Controller. A client thatis anchored on the Cisco WLCM roams to an access point on the 4402 controller. You then run adebug command on the 4402 controller.Which message would best describe the establishment ofthe tunnel from the foreign controller’s perspective?()
A Cisco WCS version 4.0 has been installed on a server with a dual Pentium 3.0 GHz processor,4GB RAM, and an 80 GB hard drive. A location appliance has been incorporated into the networkand is being monitored by the Cisco WCS. There are 3000 devices to be tracked but not all of themare being tracked on the Cisco WCS.What can be done to correct the problem?()
Which of the following accurately represents the functionality of a lightweight access point configured to operate in sniffer AP mode?()
You are using ADU and are authenticated and associated to an access point. However, you are unable to obtain an IP address.Which of these has caused this problem?()
You review the Failed Attempts logs on an AAA server and find: "unknown network access servererror." Which failure could produce this error?()
The Cisco Wireless Location Appliance provides an audit trail for each device tracked for up to how many days?()
On a WLAN controller, what is the default roaming bandwidth percentage reserved for voice clients?()
Which of the following parameter sets must be configured on the Cisco Wireless Location Appliance?()