A.debug dhcp enable
B.debug dhcp status enable
C.debug dhcp packet enable
D.enable debug dhcp packet
您可能感興趣的試卷
你可能感興趣的試題
You are troubleshooting a one-way call problem with a cisco 7920 wireless ip phone on a standalone wlan.
What may cause this problem？（）
A.the minimum data rate is not set to 11 mbps.
B.an address resolution protocol has been disabled
C.publicly secure packet forwarding is enabled
D.the access point is set to the least congested channel.
A.35
B.50
C.100
D.250
A.7
B.60
C.14
D.30
A.mac os x
B.windows 2000 sp4
C.solaris 10
D.windows server 2003
E.debian linux
A.45
B.60
C.15
D.30
A.client traffic allowed， data captured on all channels
B.client traffic allowed， data captured on a single channel
C.no client traffic allowed， data captured on a single channel
D.no client traffic allowed， data captured on all channels
You are installing a cisco 4402 series wireless lan controller.
What type of interface is used on the uplink port？（）
A.1000base-x mini-gbic
B.10/100/1000 mbps rj45
C.10/100 mbps rj45
D.1000base-sx
A.interference，utilization，and rf diffraction
B.clients，utilization，and multipath interference
C.noise，interference，and coverage holes
D.noise interference，and multipath interference
Static wep is configured on the access point. you are authenticated and associated to the access point but are unable to obtain an ip address.
Which of the following will cause this problem？（）
A.invalid radio type selected
B.no wep key configured on the client
C.invalid ssid configured
D.invalid wep key
An reap was supporting 16 wlans， but now it only supports one.
What happened to cause the change？（）
A.controller connectivity has been lost.
B.the access point lost its configuration.
C.the access point was rebooted.
D.an access point firmware upgrade is in progress.
最新試題
If it is properly deployed， a controller-based access point is capable of monitoring all VLANs on anetwork when you select which of the following modes from the AP Mode drop-down menu onthe controller？（）
A client roams from H-REAP AP1 to H-REAP AP2. The client is unable to associate to H-REAP AP2.H-REAP AP2 has six other clients associated to it， which continue to pass traffic.What has causedthis problem？（）
You have just finished aligning a Cisco Aironet 1400 Series Wireless Bridge link using installationmode. When you set the link back to operational mode you loose association to the root bridge.Which action will correct the problem？（）
The IOS of a North American Cisco Aironet 1130AG Series standalone access point has becomecorrupt. You must therefore reload the TFTP firmware.Before you press and hold the MODEbutton， you should verify that the file name is which of the following？（）
You are installing a Cisco Aironet 1000 Series controller-based access point. When you boot it， allthe LEDs on the access point blink together.What does this indicate about the access point？（）
You are troubleshooting a problem with a Cisco 7920 wireless IP phone that is causing the phoneto drop calls. The problem appears to be roaming bandwidth issue. In order to verify what kind ofissue it is， you decide to increase the bandwidth reserve for roaming on the WLAN controller tomaximum.What level do you set the bandwidth to？（）
Which of the following parameter sets must be configured on the Cisco Wireless Location Appliance？（）
You are configuring an RF group of controllers that coordinate Radio Resource Management calculations.What is the maximum number of WLAN controllers that you can add？（）
You want to dynamically assign users to an 802.1Q VLAN as a result of their authentication. Inorder to accomplish this.Which two IETF RADIUS attributes should you configure on the CiscoSecure ACS？ （）
You are trying to change the polling parameters used by the location manager via the Cisco WCS，and your request is being denied. What is wrong？（）