On your newly installed router, you apply the access list illustrated below to interface Ethernet 0 on a Cisco router. The interface is connected to the 192.168.1.8/29 LAN.
access-list 123 deny tcp 192.168.166.18 0.0.0.7 eq 20 any
access-list 123 deny tcp 192.168.166.18 0.0.0.7 eq 21 any
How will the above access lists affect traffic?（）
A. All traffic will be allowed to exit E0 except FTP traffic.
B. FTP traffic from 192.168.166.19 to any host will be denied.
C. FTP traffic from 192.168.166.22 to any host will be denied.
D. All traffic exiting E0 will be denied.
E. All FTP traffic to network 192.168.166.18/29 from any host will be denied.
您可能感興趣的試卷
你可能感興趣的試題
A. TestKingB> telnet
B. TestKingB > ping
C. TestKingB > trace
D. TestKingB > show ip route
E. TestKingB > show interface
F. TestKingB > show cdp neighbors
A. ping
B. trace
C. show ip route
D. show interface
E. show cdp neighbors
A. Serial 0 is up, line protocol is up
B. Serial 0 is up, line protocol is down
C. Serial 0 is down, line protocol is down
D. Serial 0 is down, line protocol is up
E. Serial 0 is administratively down, line protocol is down
F. Serial 0 is administratively down, line protocol is up
There is a connectivity problem between the serial 0/0 interface of router TESTKING1 and the serial 0/0 interface of TESTKING2. A leased line point to point circuit is installed between these two routers. The output from the "show interface serial 0/0" command is displayed below for each of these routers:
From your observations of the above exhibit, what is the underlying cause of the problem?（）
A. The loopback is not set.
B. The serial cable is faulty.
C. The subnet mask is not configured properly.
D. The IP address is not configured properly.
E. The Layer 2 frame types are not compatible.
F. The keepalive setting is not configured properly.
The relevant configuration files for the TestKing1 and TestKing2 routers are displayed below:
With due consideration to the command outputs, which of the following reasons would you attribute the connectivity problem between the two routers?（）
A. The authentication needs to be changed to PAP for both routers.
B. The serial IP addresses of routers are not on the same subnet.
C. The username/password combination is incorrectly configured.
D. The router names are incorrectly configured.
A. ICMP echo request
B. Information interrupt request
C. Timestamp reply
D. Source quench
E. None of the above
The Testking router is running RIP as the routing protocol, and the IP routing table is displayed below:
Gateway of last resort is 10.1.2.2 to network 0.0.0.0
10.0.0.0/24 is subnetted, 2 subnets
R 10.1.3.0 [120/1] via 10.1.2.2, 00:00:00, Serial0/0
C 10.1.2.0 is directly connected, Serial0/0
C 10.1.5.0 is directly connected, Serial0/1
C 10.1.6.0 is directly connected, FastEthernet0/0
R* 0.0.0.0/0 [120/1] via 10.1.5.5, 00:00:00, Serial0/1
Based on the output above, if an administrator pings host 10.1.8.5 from host
10.1.6.100, how will the router TestkingA process the ICMP packets?（）
A. The packets will be discarded.
B. The packets will be routed out the S0/0 interface.
C. The packets will be routed out the S0/1 interface.
D. The packets will be routed out the Fa0/0 interface.
E. The packets will be routed through the 10.1.2.2 gateway.
A. duplex mismatch
B. a routing loop
C. trunking mode mismatch
D. improperly configured root bridge
E. improperly configured static VLAN
While troubleshooting connectivity issues, you log into a remote router. From there,you wish to see the layer 1 and layer 2 status of the interface.
Which of the following IOS commands would you issue to check the current IP addressing, as well as theyer 1 and layer 2 status of an interface?（）
A. TK1# show version
B. TK1# show protocols
C. TK1# show interfaces
D. TK1# show controllers
E. TK1# show ip interface
F. TK1# show startup-config
While troubleshooting a connectivity issue from a PC you obtain the following information:
Local PC IP address: 190.0.3.35/24
Default Gateway: 190.0.3.1
Remote Server: 190.0.5.250/24
You then conduct the following tests from the local PC:
Ping 127.0.0.1 - Unsuccessful
Ping 190.0.3.35 - Successful
Ping 190.0.3.1 - Unsuccessful
Ping 190.0.5.250 - Unsuccessful
What is the underlying cause of this problem?（）
A. TCP/IP not correctly installed
B. Local physical layer problem
C. NIC not functioning
D. Remote physical layer problem
最新試題
The following access list was applied outbound on he E0 interface connected to the 192.168.1.8/29 LAN:access-list 123 deny tcp 192.168.1.8 0.0.0.7 eq 20 anyaccess-list 123 deny tcp 192.168.1.9 0.0.0.7 eq 21 anyWhat effect will this access list have?（）
You are configuring a new Catalyst switch that you want to manage remotely from workstations on other network segments within your enterprise.Which of the following are required to allow remote management of the switch over IP?（）
A router with a serial interface will be used for an ISDN link.What other function group devices are required to complete the connection to the service provider? （）
Which statement describes the rule of split horizon?（）
An administrator would like to configure a switch over a virtual terminal connection from locations outside of the local LAN. Which of the following are required in order for the switch to be configured from a remote location? （）
Which connections allow the use of full-duplex Ethernet?（）
Which Frame Relay feature is responsible for transmitting keepalives to ensure that the PVC does not shut down because of inactivity?（）
TestKing.com has allocated the IP add 199.144.27.0 is its network, to provide flexibility for the LAN design, a subnet mask of 255.255.255.240 has been chosen. Which of the following address can be assigned to LAN on the resulting subnets.（）
Which characteristics are representative of a link-state routing protocol?（）
Which of the following host addresses are member of networks that can be routed across the public Internet? （）