A. ICMP echo request
B. Information interrupt request
C. Timestamp reply
D. Source quench
E. None of the above
您可能感興趣的試卷
你可能感興趣的試題
The Testking router is running RIP as the routing protocol, and the IP routing table is displayed below:
Gateway of last resort is 10.1.2.2 to network 0.0.0.0
10.0.0.0/24 is subnetted, 2 subnets
R 10.1.3.0 [120/1] via 10.1.2.2, 00:00:00, Serial0/0
C 10.1.2.0 is directly connected, Serial0/0
C 10.1.5.0 is directly connected, Serial0/1
C 10.1.6.0 is directly connected, FastEthernet0/0
R* 0.0.0.0/0 [120/1] via 10.1.5.5, 00:00:00, Serial0/1
Based on the output above, if an administrator pings host 10.1.8.5 from host
10.1.6.100, how will the router TestkingA process the ICMP packets?（）
A. The packets will be discarded.
B. The packets will be routed out the S0/0 interface.
C. The packets will be routed out the S0/1 interface.
D. The packets will be routed out the Fa0/0 interface.
E. The packets will be routed through the 10.1.2.2 gateway.
A. duplex mismatch
B. a routing loop
C. trunking mode mismatch
D. improperly configured root bridge
E. improperly configured static VLAN
While troubleshooting connectivity issues, you log into a remote router. From there,you wish to see the layer 1 and layer 2 status of the interface.
Which of the following IOS commands would you issue to check the current IP addressing, as well as theyer 1 and layer 2 status of an interface?（）
A. TK1# show version
B. TK1# show protocols
C. TK1# show interfaces
D. TK1# show controllers
E. TK1# show ip interface
F. TK1# show startup-config
While troubleshooting a connectivity issue from a PC you obtain the following information:
Local PC IP address: 190.0.3.35/24
Default Gateway: 190.0.3.1
Remote Server: 190.0.5.250/24
You then conduct the following tests from the local PC:
Ping 127.0.0.1 - Unsuccessful
Ping 190.0.3.35 - Successful
Ping 190.0.3.1 - Unsuccessful
Ping 190.0.5.250 - Unsuccessful
What is the underlying cause of this problem?（）
A. TCP/IP not correctly installed
B. Local physical layer problem
C. NIC not functioning
D. Remote physical layer problem
Part of the configuration files for routers testking1 and testking2 are displayed below:
If you were to enter the "show interface serial 0" command on router testking1,which of the following will be displayed?（）
A. Serial 0 is down, line protocol is down
B. Serial 0 is up, line protocol is up
C. Open: IPCP, CDPCP
D. LCP closed
E. LCP open
A. Show ip protocols
B. Show ip route rip
C. Debug ip rip
D. Debug ip updates
E. Debug ip transactions
A. TestKing# show ip route *
B. TestKing# debug eigrp route
C. TestKing# debug ip eigrp
D. TestKing# debug ip protocols eigrp
E. TestKing# show ip route eigrp
The following was issues on router TestKingA:
TestKingA #show ip ospf neighbor
Neigbor ID PRI State Dead Time Address Interface
192.168.1.2 1 Full/- 00:00:37 192.168.1.2 Serial1
Which type of OSPF network will provide the output shown in the graphic?（）
A. FDDI
B. nonbroadcast multiaccess
C. broadcast multi-access
D. point-to-point
A. TestKing# show eigrp entries
B. TestKing# show protocols
C. TestKing# debug eigrp routes
D. TestKing# show ip route eigrp
E. TestKing# show route eigrp
最新試題
What is the purpose of typing o/r 0x2142 during a password recover procedure on a 2500 series router?（）
Identify three valid host addresses in the 192.168.27.0 network with a subnet mask of 255.255.255.240. （）
TestKing.com has allocated the IP add 199.144.27.0 is its network, to provide flexibility for the LAN design, a subnet mask of 255.255.255.240 has been chosen. Which of the following address can be assigned to LAN on the resulting subnets.（）
Which statement describes the rule of split horizon?（）
A router with a serial interface will be used for an ISDN link.What other function group devices are required to complete the connection to the service provider? （）
A Class C network address has been subnetted with a /27 mask.Which of the following addresses is a broadcast address for one of the resulting subnets?（）
Which of the following correctly describe steps in the OSI data encapsulation process?（）
What should the configuration register value be after successfully completing the password recover procedure and returning the router to normal operation? （）
An administrator would like to configure a switch over a virtual terminal connection from locations outside of the local LAN. Which of the following are required in order for the switch to be configured from a remote location? （）
You are configuring a new Catalyst switch that you want to manage remotely from workstations on other network segments within your enterprise.Which of the following are required to allow remote management of the switch over IP?（）