A. TestKingB> telnet
B. TestKingB > ping
C. TestKingB > trace
D. TestKingB > show ip route
E. TestKingB > show interface
F. TestKingB > show cdp neighbors
您可能感興趣的試卷
你可能感興趣的試題
A. ping
B. trace
C. show ip route
D. show interface
E. show cdp neighbors
A. Serial 0 is up, line protocol is up
B. Serial 0 is up, line protocol is down
C. Serial 0 is down, line protocol is down
D. Serial 0 is down, line protocol is up
E. Serial 0 is administratively down, line protocol is down
F. Serial 0 is administratively down, line protocol is up
There is a connectivity problem between the serial 0/0 interface of router TESTKING1 and the serial 0/0 interface of TESTKING2. A leased line point to point circuit is installed between these two routers. The output from the "show interface serial 0/0" command is displayed below for each of these routers:
From your observations of the above exhibit, what is the underlying cause of the problem?()
A. The loopback is not set.
B. The serial cable is faulty.
C. The subnet mask is not configured properly.
D. The IP address is not configured properly.
E. The Layer 2 frame types are not compatible.
F. The keepalive setting is not configured properly.
The relevant configuration files for the TestKing1 and TestKing2 routers are displayed below:
With due consideration to the command outputs, which of the following reasons would you attribute the connectivity problem between the two routers?()
A. The authentication needs to be changed to PAP for both routers.
B. The serial IP addresses of routers are not on the same subnet.
C. The username/password combination is incorrectly configured.
D. The router names are incorrectly configured.
A. ICMP echo request
B. Information interrupt request
C. Timestamp reply
D. Source quench
E. None of the above
The Testking router is running RIP as the routing protocol, and the IP routing table is displayed below:
Gateway of last resort is 10.1.2.2 to network 0.0.0.0
10.0.0.0/24 is subnetted, 2 subnets
R 10.1.3.0 [120/1] via 10.1.2.2, 00:00:00, Serial0/0
C 10.1.2.0 is directly connected, Serial0/0
C 10.1.5.0 is directly connected, Serial0/1
C 10.1.6.0 is directly connected, FastEthernet0/0
R* 0.0.0.0/0 [120/1] via 10.1.5.5, 00:00:00, Serial0/1
Based on the output above, if an administrator pings host 10.1.8.5 from host
10.1.6.100, how will the router TestkingA process the ICMP packets?()
A. The packets will be discarded.
B. The packets will be routed out the S0/0 interface.
C. The packets will be routed out the S0/1 interface.
D. The packets will be routed out the Fa0/0 interface.
E. The packets will be routed through the 10.1.2.2 gateway.
A. duplex mismatch
B. a routing loop
C. trunking mode mismatch
D. improperly configured root bridge
E. improperly configured static VLAN
While troubleshooting connectivity issues, you log into a remote router. From there,you wish to see the layer 1 and layer 2 status of the interface.
Which of the following IOS commands would you issue to check the current IP addressing, as well as theyer 1 and layer 2 status of an interface?()
A. TK1# show version
B. TK1# show protocols
C. TK1# show interfaces
D. TK1# show controllers
E. TK1# show ip interface
F. TK1# show startup-config
While troubleshooting a connectivity issue from a PC you obtain the following information:
Local PC IP address: 190.0.3.35/24
Default Gateway: 190.0.3.1
Remote Server: 190.0.5.250/24
You then conduct the following tests from the local PC:
Ping 127.0.0.1 - Unsuccessful
Ping 190.0.3.35 - Successful
Ping 190.0.3.1 - Unsuccessful
Ping 190.0.5.250 - Unsuccessful
What is the underlying cause of this problem?()
A. TCP/IP not correctly installed
B. Local physical layer problem
C. NIC not functioning
D. Remote physical layer problem
Part of the configuration files for routers testking1 and testking2 are displayed below:
If you were to enter the "show interface serial 0" command on router testking1,which of the following will be displayed?()
A. Serial 0 is down, line protocol is down
B. Serial 0 is up, line protocol is up
C. Open: IPCP, CDPCP
D. LCP closed
E. LCP open
最新試題
Which command is required for connectivity in a Frame Relay network if Inverse ARP is not operational? ()
Which of the following if addresses can be assigned to host devices?()
Which connections allow the use of full-duplex Ethernet?()
All WAN links is side the TestKing.com network use PPP with for authentication security. Which command will display the CHAP authentication process as it occurs between two routers in the network?()
What is the purpose of typing o/r 0x2142 during a password recover procedure on a 2500 series router?()
Which characteristics are representative of a link-state routing protocol?()
Which Frame Relay feature is responsible for transmitting keepalives to ensure that the PVC does not shut down because of inactivity?()
What feature of a networks switch allows an administrative to create separate broadcast domains?()
A technician at TestKing needs to update the network documentation. One of the tasks includes documenting the name of the IOS image file of each router in the network.Which commands could be used to find this information?()
A router with a serial interface will be used for an ISDN link.What other function group devices are required to complete the connection to the service provider? ()