A. from 10:00:00:00:00:00:00:00 to 10:FF:FF:FF:FF:FF:FF:FF
B. from 20:00:00:00:00:00:00:00 to 20:FF:FF:FF:FF:FF:FF:FF
C. from 30:00:00:00:00:00:00:00 to 30:FF:FF:FF:FF:FF:FF:FF
D. from 40:00:00:00:00:00:00:00 to 40:FF:FF:FF:FF:FF:FF:FF
您可能感興趣的試卷
你可能感興趣的試題
A. NPIV provides a means to assign multiple Fibre Channel IDs to a single N-port.
B. NPIV can be enabled on a per-VSAN basis.
C. NPIV requires a "write erase" and then reload the switch in order to come up into NPIV mode.
D. NPIV is a Cisco proprietary feature and as such works only between two Cisco switches.
E. NPIV must not be enabled on a switch that is also running N-port virtualization.
A. 2
B. 3
C. 4
D. 6
E. 12
A. After enabling NPIV, switch interfaces can only be placed into NP, F, or SD modes of operation.
B. NPV devices log in to NPIV devices.
C. NPIV requires the Enterprise License Package.
D. NPIV is supported on the Cisco MDS, N7K, and N5K families of switches.
E. A director class switch should not be placed into NPIV mode.
A. B200
B. C210
C. B250
D. C260
E. C460
A. 800 MHz
B. 900 MHz
C. 1066 MHz
D. 1333 MHz
E. 1666 MHz
A. Dual-rank DIMMs are not supported.
B. 16-GB DIMMs are too slow.
C. The largest DIMM an Intel 55xx or 56xx CPU can address is 32 GB
D. The memory bus would be too long.
E. The blade would run too hot.
A. Missing control VLAN in VSM configuration
B. Missing packet VLAN in VSM configuration
C. VSM has no network connection to vCenter
D. VSM extension key is not installed on vCenter
E. vCenter extension key is not installed on VSM
The network administrator is adding a new N1Kv to the vCenter, however, the administrator does not see the new switch under the networking tab of vCenter.
The administrator issues the following command on the VSM to troubleshoot:
VSM# show svs connections
connection VC:
ip address: 10.10.10.30
remote port: 80
protocol: vmware-vim https
certificatE. default
datacenter namE. DC1
DVS uuiD. 67 32 30 50 a6 d2 49 64-9e 1c 5f 49 e3 af 55 99
config status: Disabled
operational status: Disconnected sync status: -
version: -
When attempting to fix the issue, the following error is seen:
VSM-PRI-188# conf
VSM-PRI-188(config)# svs connection VC
VSM-PRI-188(config-svs-conn)# connect
ERROR: [VMWARE-VIM] Extension key was not registered before its use
What is the cause of the error?()
A. Missing control VLAN in VSM configuration
B. Missing packet VLAN in VSM configuration
C. VSM has no network connection to vCenter
D. VSM extension key is not installed on vCenter
E. vCenter extension key is not installed on VSM
Given the following configuration:
port-profile type ethernet DATA-UPLINK
vmware port-group
switchport trunk allowed vlan 1-3967,4048-4093
channel-group auto mode on
no shutdown
state enabled
port-profile type ethernet MGMT-UPLINK
vmware port-group
switchport trunk allowed vlan 10-12
channel-group auto mode on
no shutdown
state enabled
VEMs are seen to be joining and then are lost from the Cisco VSM. How would you resolve this issue?()
A. Remove second NIC from each port profile
B. Remove VEM from VSM (no vem X), remove NICs, and reinsert
C. Ensure that VLANs on uplink profiles are not overlapping
D. Reinstall VEM
E. Issue the command "module vem X execute vemcmd set pinning module vsm 1"
A. Send monitored traffic to a VLAN
B. Send monitored traffic to a remote VEM over L2
C. Receive monitored traffic on a vEthernet interface
D. Send monitored traffic to an IP destination
最新試題
Which is true when describing a connection replication in Cisco ACE?()
Refer to the exhibit.The Cisco UCS domain is operating in switching mode. A network administrator notices that no traffic is traversing the uplinks on Fabric Interconnect B (Path C). Which actions might be used to change this behavior?()
Refer to the exhibit. According to the equipment tab in Cisco UCS Manager, which is true?()
When will an "all configuration" backup be imported into the Cisco UCS Manager?()
In a Cisco Unified Computing System, What is the "designated receiver" port in end-host mode used for?()
From the Cisco UCS CLI, how do you verify which uplink ports a blade server is using for its network connectivity?()
Which two statements about end-host mode in SAN connectivity in a Cisco UCS environment are true? ()
Given a Cisco Unified Computing System, which is a valid port type in end-host mode?()
In the event of a GSS failure in a GSS cluster, which is true?()
What interface is created when an FC Port Channel is created on a Cisco Unified Computing System?()