A. Passiveroutes are in the process of being calculated by DUAL.
B. EIGRP supports VLSM, route summarization, and routing update authentication.
C. EIGRP exchanges full routing table information with neighboring routers with every update.
D. If the feasible successor has a higher advertised distance than the successor route, it becomes the primary route.
E. A query process is used to discover a replacement for a failed route if a feasible successor is not identified from the current routing information.
您可能感興趣的試卷
你可能感興趣的試題
A. The data is moving from 10BASE-TX to 100BASE-TX.
B. The WAN encapsulation type has changed.
C. The data format has changed from analog to digital.
D. The source and destination hosts are in the same subnet.
E. The source and destination MAC addresses have changed.
A. to uniquely identify devices at Layer 2
B. to allow communication with devices on a different network
C. to differentiate a Layer 2 frame from a Layer 3 packet
D. to establish a priority system to determine which device gets to transmit first
E. to allow communication between different devices on the same network
F. to allow detection of a remote device when its physical address is unknown
A. It converges quickly.
B. OSPF is a classful routing protocol.
C. It uses cost to determine the best route.
D. It uses the DUAL algorithm to determine the best route.
E. OSPF routers send the complete routing table to all directly attached routers.
F. OSPF routers discover neighbors before exchanging routing information.
A.10.15.32.17
B.17.15.66.128
C.66.55.128.1
D.135.1.64.34
E.129.33.192.192
F.192.168.5.63
A.172.31.17.4/30
B.172.31.51.16/30
C.172.31.64.0/18
D.172.31.80.0/22
E.172.31.92.0/22
F.172.31.192.0/18
A. The next routing update can be expected in 35 seconds.
B. The IP address 10.10.10.6 is configured on S0/1.
C. The IP address 10.10.10.8 is configured on S0/1.
D. This route is using the default administrative distance.
E. The 10.10.10.8 network is two hops away from this router.
A. the IP address of Switch 1
B. the MAC address of Switch 1
C. the IP address of Host C
D. the MAC address of Host C
E. the IP address of the router's E0 interface
F. the MAC address of the router's E0 interface
A.buffering
B.cut-through
C.windowing
D.congestion avoidance
E.load balancing
A.115.64.8.32
B.115.64.7.64
C.115.64.6.255
D.115.64.3.255
E.115.64.5.128
F.115.64.12.128
An administrator is unsuccessful in adding VLAN 50 to aswitch. While troubleshooting the problem, the administrator views the output of the show vtp status command, which is displayed in the graphic. What commands must be issued on this switch to add VLAN 50 to the database?（）
A. Switch(config-if)# switchport access vlan 50
B. Switch(vlan)# vtp server
C. Switch(config)# config-revision 20
D. Switch(config)# vlan 50 name Tech
E. Switch(vlan)# vlan 50
F. Switch(vlan)# switchport trunk vlan 50
最新試題
At which layer of the OSI model is RSTP used to prevent loops?（）
At which layer of the OSI model dose PPP perform?（）
On which options are standard access list based?（）
Three access ports have been installed and configured to a small office.What term defines the wireless topology?（）
A network administrator is trying to add a new router into an established OSPF network.The networks attached to the new router do not appear in the routing tables of the other OSPF routers.Given the information in the partial configuration shown below,what configuration error is causing this problem?（）Router(config)#router ospf 1Router(config-router)#network 10.0.0.0 255.0.0.0 area 0
Which pairing reflects a correct protocol-and-metric relationship?（）
Which command is used to display the collection of OSPF link states?（）
Which cisco ios command can help to determine the timing of various debug events,relative to each other,when you are debugging a complicated router issue?（）
Which statement describes the rule of split horizon?（）
The network administrator cannot to switch 1 over a telnet session,although the hosts attached to switch 1 can ping the interface Fa0/0 of the router.Given the information in the graphic and assuming that the router and switch2 are configured properly,which of the following commands should be issued on switch 1 to correct this problem?（）