A. Up to 25 m bus length
B. Only one device per SCSI bus
C. Up to 16 devices per SCSI bus
D. Half-duplex operation
E. Full-duplex operation
您可能感興趣的試卷
你可能感興趣的試題
A. Ethernet FCS
B. Source address
C. Destination address
D. EtherType
E. Protocol type
A. It is required to establish the point-to-point FCoE links with the first switch in the path.
B. It is required to establish the point-to-point FCoE links with any switch across multiple Ethernet segments.
C. It is not used to build the FCoE links.
D. It is used to ensure lossless transport.
A. Fibre Channel ports must be configured from the first port in the module.
B. Ethernet ports must be configured from the last port in the module.
C. Fibre Channel ports must be configured from the last port in the module.
D. Ethernet ports must be configured from the first port in the module.
A. LLDP transmit and receive are disabled
B. The initiator server has no connectivity to the target storage
C. FIP negotiation timing
D. Peer does not support LLDP
E. VSAN trunk protocol has been enabled
A. Server’s CNA does not support DCBX and PFC TLV was not negotiated.
B. A "no-drop" class has not been configured for FCoE
C. The system is running with the default QOS policies.
D. The link is oversubscribed.
A. show flogi database
B. show system fc login
C. show npv flogi-table
D. show npv fcns database
E. show interface vfc X flogi
F. show interface flogi
A. Priority flow control
B. Buffer-to-buffer credits
C. TCP retransmission
D. Ethernet checksum
E. QoS policies
A. Cannot be disabled
B. Cannot have the CoS changed
C. Can have "Packet Drop" enabled
D. Is multicast optimized
E. Can have the MTU changed
A. 1
B. 2
C. 4
D. 5
E. 16
A. It’s hard-set and cannot be disabled
B. It’s configurable， with an upper limit of 16
C. It’s hard-set but cannot disable best-effort and Fibre Channel
D. It’s hard-set but can disable all but one class
E. It’s configurable with an upper limit of eight
最新試題
Which three statements are possible causes for the "fltAdaptorHostIfLink-down" fault in UCS Manager？ （）
Which GSS "source access list" is used to allow access to GSS by clients when GSS is being used as the DNS？（）
What is the purpose of this command in a Cisco Application Control Engine？（） switch/Admin# show np 1 me-stats "-F0 v"
Which statement is true regarding Backup tasks in Cisco UCS？（）
On a Cisco Unified Computing System （UCS）， which two statements regarding Ethanalyzer are true？（）
Refer to the exhibit.The Cisco UCS domain is operating in switching mode. A network administrator notices that no traffic is traversing the uplinks on Fabric Interconnect B （Path C）. Which actions might be used to change this behavior？（）
Given a Cisco Unified Computing System， which is a valid port type in end-host mode？（）
Your company wants Server 1/eth0 （vNIC 1） configured so that it always uses Fabric Interconnect A Port Channel 1 （Po1） when it communicates with anything outside of the Cisco UCS domain. However， if vNIC 1 fails over to Fabric Interconnect B using fabric failover， then vNIC 1 can any uplink port on Fabric Interconnect B. Which statements are true？ （）
Which are valid statements about Cisco Virtual Interface Card （VIC）？ （）
Given the following output： san-port-channel 12 is up Hardware is Fibre Channel Port WWN is 24：0c：00：0d：ec：d3：5c：00 Admin port mode is NP， trunk mode is on Port mode is NP Port vsan is 1 Speed is 8 Gbps Member[1] ： fc2/3 Member[2] ： fc2/4 What does "Speed is 8 Gbps" indicate？（）