A. Because Frame Relay IETF encapsulation is only configurable at interface level, you must use IETF encapsulation on all routers.
B. This is not a possible scenario. A dedicated Frame Relay link to RemoteB is mandatory at the central office.
C. The router at RemoteB must be replaced by a Cisco router.
D. Use Frame Relay IETF encapsulation on a per-VC basis on the central office router.
E. There is a problem in the Frame Relay cloud, because Cisco routers are compatible with IETF Frame Relay.
您可能感興趣的試卷
你可能感興趣的試題
A.ip verify unicast source reachable-via any
B.ip verify unicast reverse-path
C.ip verify unicast reverse-path loose
D.ip verify unicast reverse-path strict
A. Because the configuration revision of the new switches is lower than the rest of the network,it can change the VLAN database of the other switches.
B. As a VTP server, the new switch deleted all VLANs of the network.
C. Erasing VLANs increases the VTP configuration revision.
D. Since the configuration revision of the network is higher than the new switch,the VLAN database was automatically synchronized.
Refer to the exhibit. Users from the Engineering VLAN complain that every time Business VLAN users have a network connectivity issue, the Engineering VLAN users usually have problems experiencing slow response or network connectivity problems. After troubleshooting, an unauthorized switch 2 was found. This unauthorized switch has been a regular problem, assuming the root bridge function under the spanning-tree domain and causing the
Engineering VLAN to be unstable. Which three of these actions could be suggested to fix the problem?()
A. Upgrade Spanning Tree Protocol to Rapid Spanning Tree Protocol.
B. Change Business VLAN PCs to switch 1 and switch 4.
C. Force the root bridge to be switch 2, instead.
D. Adjust spanning-tree timers (max-age and forward-delay).
E. Shut down all unused ports.
F. Use MSTP to separate the Engineering VLAN from the Business VLAN to optimize spanning-tree convergence time within each VLAN
A.Binding should be manually configured.
B.It is not supported if IEEE 802.1x port-based authentication is enabled.
C.The DHCP server must support option 82, or the client is not assigned an IP address.
D.It filters based on source IP address only.
Refer to exhibits 1 and 2. In exhibit 1, all users on the LAN segment use router A as the active HSRP router. Router B is the standby router for the HSRP. In exhibit 2, the network management team reported that there is no utilization on the WAN link B. To solve this problem, you decide to change the logical topology of your LAN, but you are not sure about what changes must be made. You must manage HSRP or change it to another protocol in order to provide the most scalable design, automatic redundancy, and load balancing. Which one of these actions would be the best choice? ()
A. Use MHSRP, with three users using router A as the default gateway and three users using router B as the default gateway.
B. Keep HSRP and activate PBR to redirect half of the traffic to the other WAN link.
C. Use the backup interface on the WAN link B to provide load balancing for all users.
D. Use GLBP instead, because it provides you with up to three MAC addresses for the same default gateway virtual IP address.
E. Use GLBP instead, because it provides you with up to four MAC addresses for the same default gateway virtual IP address.
A.SMTP
B.ICMP
C.BGP
D.SSH
E.RTP
F.BitTorrent
G.VTP
Refer to the exhibit. The Layer 2 network uses VTP to manage its VLAN database. A network designer created all VLANs on the VTP server (switch 1) and it has been advertised through VTP to all other VTP clients (switches 2 through 4). Due to network growth, a network operator decided to add a new switch between switch 1 and switch 3. The network operator has been instructed to use a refurbished switch and use a VTP client. Which three of these factors should the network operator consider to minimize the impact of adding a new switch?()
A. Pay special attention to the VTP revision number, because the higher value takes the priority.
B. Configure all VLANs manually on the new switch in order to avoid connectivity issues.
C. A trunk should be established between the new switch and switches 1 and 3 as VTP only runs over trunk links.
D. Set at least the VTP domain name and password to get the new switch synchronized.
E. An ISL trunk should be established between the new switch and switches 1 and 3, because VTP only runs over ISL.
F. Pay special attention to the VTP revision number, because the lower value takes the priority.
A.It is used in multihome network scenarios.
B.It can be used with BGP to mitigate DoS and DDoS.
C.It does not need to have CEF enabled.
D.It is enabled via the interface level command ip verify unicast reverse-path.
E.It cannot be used with "classification" access lists.
A.Do not enable all the signatures at the same time.
B.Do not enable the ICMP signature.
C.Disable the Zone-Based Policy Firewall because it is not compatible with Cisco IOS IPS.
D.Disable CEF because it is not compatible with Cisco IOS IPS. .
A.It is a Cisco proprietary protocol.
B.It runs on TCP port 59. .
C.Authentication and authorization are done at different stages.
D.TACACS+ encrypts the entire body of the packet, but leaves a standard TACACS+ header.
E.It is an industry standard protocol.
F.TACACS+ encrypts both the entire body of the packet and the TACACS+ header.
最新試題
When STP UplinkFast is enabled on a switch utilizing the default bridge priority, what will the new bridgepriority be changed to?()
All of these are fundamental building blocks of differentiated services Traffic Conditioner Block exceptwhich one?()
Which message type is constructed and sent from an MSDP router to its MSDP peers when it receives a PIM register message knowing that the MSDP router is also configured as an RP for the PIM domain?()
What is true about Unicast RPF in strict mode?()
What is the command to configure RSVP to reserve up to one-tenth of a Gigabit link,but only allow eachindividual flow to use 1 MB/s?()
Which protocol and port have been assigned by IANA for RADIUS authentication?()
In GLBP,which router will answer on client ARP requests?()
Based on the output provided in the exhibit, to which address or location will the router forward a packet sent to 192.168.32.1?()
Which command is used to enable SSM with the range 232.0.0.0 - 255.0.0.0?()
Which two are differences between IGMPv2 and IGMPv3 reports?()