A.Do not enable all the signatures at the same time.
B.Do not enable the ICMP signature.
C.Disable the Zone-Based Policy Firewall because it is not compatible with Cisco IOS IPS.
D.Disable CEF because it is not compatible with Cisco IOS IPS. .
您可能感興趣的試卷
你可能感興趣的試題
A.It is a Cisco proprietary protocol.
B.It runs on TCP port 59. .
C.Authentication and authorization are done at different stages.
D.TACACS+ encrypts the entire body of the packet， but leaves a standard TACACS+ header.
E.It is an industry standard protocol.
F.TACACS+ encrypts both the entire body of the packet and the TACACS+ header.
A.it is used for load balancing in bidirectional PIM
B.it is used for redundancy in bidirectional PIM
C.it is used for redundancy in PIM-SM
D.it is used for load balancing in PIM-SM
Refer to the exhibit. Look at the command output. What can you use to prevent this behavior？ （）
A. UDLD （UniDirectional Link Detection）
B. spanning-tree loopguard
C. VTP mode transparent
D. switchport mode desirable
A.Membership Query
B.Membership Report
C.Membership Delay
D.Backward Compatible IGMPv1 Report Message
A.Source Specific Multicast and IGMPv2
B.Announcing multicast sources to BGP speakers
C.Anycast RP
D.Intradomain multicast routing
Refer to the exhibit. Look at the command output. Assume that there is no other path， and the configuration is correct. What would be the consequences of this situation？（）
A. Users in SW1 can ping SW2 but not vice versa.
B. Users in SW2 can ping SW1 but not vice versa.
C. Users in SW1 and SW2 can ping each other.
D. Users in SW1 and SW2 cannot ping each other.
A.to prevent multicast packets from looping
B.to prevent PIM packets from looping
C.to instruct PIM where to send a （*， G） or （S， G） join message
D.to prevent multicast packets from looping and to instruct PIM where to send a （*， G） or （S， G） joinmessage
A.232.0.0.0/8
B.239.0.0.0/8
C.232.0.0.0/4
D.FF3x：：/32
E.FF2x：：/32
F.FF3x：：/16
Refer to the exhibit. Look at the command output. What would be the most probable reason for this port-ID mismatch？（）
A. spanning-tree misconfiguration
B. speed mismatch configuration
C. cabling problem
D. configuration problem
A.PIM-SM
B.PIM-DM
C.PIM-SSM
D.DVMRP
最新試題
Which of these best describes the actions taken when a VTP message is received on a switch configuredwith the VTP mode "transparent"？（）
How does an IPv6 router deal with a packet that is larger than the outgoing interface MTU？（）
Which three message types are valid PIMv2 message types？（）
Which protocol and port have been assigned by IANA for RADIUS authentication？（）
Choose two commands that are required to enable multicast on a router， when it is known that thereceivers use a specific functionality of IGMPv3.（）
Which two are differences between IGMPv2 and IGMPv3 reports？（）
In Layer 2 topologies， spanning-tree failures can cause loops in the network. These unblocked loops cancause network failures because of excessive traffic. Which two Catalyst 6500 features can be used to limitexcessive traffic during spanning-tree loop conditions？（）
Which three protocols or applications should be placed in a class that is configured with WRED？（）
Which two of these are used in the selection of a root bridge in a network utilizing Spanning Tree ProtocolIEEE 802.1 D？（）
What is the correct command to set the router ID for an OSPFv3 process？（）