An 802.1X client cannot authenticate to an autonomous access point configured for multiple
VLANs. The native VLAN does not have an SSID configured.
Which one of the following links being down would prevent the clients from authenticating？（）
A.between the RADIUS and the access point
B.between the client’s VLAN and the WLSE
C.between the native VLAN and the WLSE
D.between the client’s VLAN and the RADIUS
您可能感興趣的試卷
你可能感興趣的試題
In a deployment using the lightweight access points， clients set up to authenticate with EAP-PEAPor EAP-Cisco Wireless （LEAP） cannot authenticate. Upon inspection of the Failed Attempts reportyou see the following error： "Unknown network access server NAS."
What two problems can causethis type of failure？（）
A.misconfigured IP address of the AAA server on the wireless controller
B.misconfigured IP address of the wireless LAN controller on the AAA server
C.misconfigured EAP type on the wireless LAN controller
D.misconfigured shared secret on the wireless LAN controller
E.misconfigured EAP type on the AAA server
Your client has deployed a Cisco Wireless Location Appliance within their warehouse environment.They have been experiencing problems with tracking objects using active RFID tags. The RFID tagdata is not being collected.
On which device would you verify that RFID status has been enabled？（）
A.Cisco WCS
B.access point
C.wireless controller
D.location manager
A.802.11b/g
B.radio
C.access point
D.802.11a
A.IP
B.TCP
C.UDP
D.IPX
Your client has deployed a Cisco Wireless Location Appliance within their warehouse environment.They have been experiencing problems with tracking objects using active RFID tags. The RFID beacon rate is 10 seconds. You have discovered an issue with the RFID timeout value.
How shouldthis value be changed？（）
A.Change the value on the wireless controller to 45 seconds.
B.Change the value on the wireless controller to 95 seconds.
C.Change the value on the Cisco WCS to 95 seconds.
D.Change the value on the Cisco WCS to 45 seconds.
A.Frame Monitoring
B.Radio Scan
C.Self-Healing
D.Client Walkabout
You are trying to deploy a configuration job to an IOS access point using the WLSE， but the jobfails.
Which of the following would cause this failure？（）
A.SNMP communities
B.Telnet/SSH user/password
C.WLCCP credentials
D.HTTP user/password
A.3
B.1
C.4
D.6
A.PSK authentication
B.EAP authentication
C.WPA authentication
D.Web authentication
VLANs have been enabled on an autonomous access point.
In order for clients associating toVLANs other than the native VLAN to receive an IP address which of the following must beconfigured？（）
A.access point Ethernet port set to SSL trunking
B.switchport set to 802.1q trunking
C.switchport set to SSL trunking
D.access point Ethernet port not set to 802.1q trunking
最新試題
An REAP was supporting 16 WLANs， but now it only supports one.What happened to cause the change？（）
You are charges with implementing a secure wireless installation which will provide Internet accessto client devices but will not allow communications between wireless clients.In addition to implementing PSPF or peer-to-peer blocking on the wireless side，which of the following actionsshould you perform on the wired infrastructure？（）
You are using ADU and are authenticated and associated to an access point. However， you are unable to obtain an IP address.Which of these has caused this problem？（）
You are installing a Cisco 4402 Series Wireless LAN Controller.What type of interface is used on the uplink port？（）
The Cisco Wireless Location Appliance provides an audit trail for each device tracked for up to how many days？（）
You are configuring an RF group of controllers that coordinate Radio Resource Management calculations.What is the maximum number of WLAN controllers that you can add？（）
What is the maximum number of wireless controllers that the highest-end Cisco WCS server canmanage？（）
You are installing a Cisco Aironet 1000 Series controller-based access point. When you boot it， allthe LEDs on the access point blink together.What does this indicate about the access point？（）
You have just finished aligning a Cisco Aironet 1400 Series Wireless Bridge link using installationmode. When you set the link back to operational mode you loose association to the root bridge.Which action will correct the problem？（）
You are configuring a wireless LAN controller for QoS.Which 802.11e user priority tag should you apply to voice applications？（）