A.RTS threshold = 1,CWmin = 4
B.RTS threshold = 4000,CWmin = 5
C.RTS threshold = 4000,CWmin = 3
D.RTS threshold = 1,CWmin = 5
您可能感興趣的試卷
你可能感興趣的試題
You review the Failed Attempts logs on an AAA server and find: "unknown network access servererror."
Which failure could produce this error?()
A.AAA client and AAA server handshake failure
B.supplicant authentication failure
C.wrong password used by the supplicant
D.failure of the wireless client and AAA server handshake
During the installation of the Cisco WCS version 4.0, an error occurs.
Where would you look for theinstallation log, in order to learn more about this error?()
A.at the root of the installation drive
B.in the Cisco WCS installation directory
C.on the desktop of the server
D.in the Cisco WCS\Logs directory
You are configuring an RF group of controllers that coordinate Radio Resource Managementcalculations.
What is the maximum number of WLAN controllers that you can add?()
A.17
B.20
C.12
D.24
A.Multicast on
B.Aggressive Load Balancing off
C. Multicast off
D.AP Fallback on
E.Aggressive Load Balancing on
F.AP Fallback off
You are installing a Cisco 4402 Series Wireless LAN Controller.
Which type of interface should you use on the controller’s distribution port?()
A.1000BASE-SX SFP
B.10/100/1000 Mbps RJ45
C.10/100 Mbps RJ45
D.10000BASE-SX
By default, on the WLAN controller for a voice application using Cisco 7921 wireless IP phones.
What is the percentage of RF bandwidth that can be dedicated to the phones?()
A.75 percent
B.85 percent
C.56 percent
D.55 percent
The IOS of a North American Cisco Aironet 1130AG Series standalone access point has becomecorrupt. You must therefore reload the TFTP firmware. Before you press and hold the MODEbutton.
You should verify that the file name is which of the following?()
A. c1130-k9w7-tar.boot
B. c1130-k9w7-tar.123-7.JA1.tar
C. c1130-k9w7-tar.default
D. c1130-k9w7-tar.recove
A.Problem Management
B.Configuration Management
C.Incident Management
D.Change Management
A.15
B.10
C.1
D.5
A mobility group is created by a Cisco WLCM and 4402 Series Wireless LAN Controller. A client thatis anchored on the Cisco WLCM roams to an access point on the 4402 controller. You then run adebug command on the 4402 controller.
Which message would best describe the establishment of the tunnel from the foreign controller’sperspective?()
A.Received Mobile Anchor Export message
B.Transmit Plumbing duplex mobility tunnel message
C.Received Plumbing duplex mobility tunnel message
D.Transmit Mobile Anchor Export message
最新試題
What is the maximum number of wireless controllers that the highest-end Cisco WCS server canmanage?()
An REAP was supporting 16 WLANs, but now it only supports one.What happened to cause the change?()
Clients using Cisco-LEAP and EAP-FAST authentication are having no problems logging on to thewireless network, but clients using PEAP are failing to log on.Which situation would result in thistype of problem?()
On a WLAN controller, what is the default roaming bandwidth percentage reserved for voice clients?()
Which of the following parameter sets must be configured on the Cisco Wireless Location Appliance?()
On a Cisco Aironet 1240AG Series standalone access point, the radio LED is dark blue and blinking,but the status LED and Ethernet LED are both off.What does this indicate?()
You want to dynamically assign users to an 802.1Q VLAN as a result of their authentication. Inorder to accomplish this.Which two IETF RADIUS attributes should you configure on the CiscoSecure ACS? ()
If it is properly deployed, a controller-based access point is capable of monitoring all VLANs on anetwork when you select which of the following modes from the AP Mode drop-down menu onthe controller?()
You have a very few Cisco 7920 wireless IP phones on your network, but lots of wireless laptops.You want to increase the bandwidth available for the laptops by decreasing the bandwidth reserved for the Cisco 7920 phones.What is the lowest percentage of voice-allocated bandwidthyou can select on the WLAN controller?()
You are using ADU and are authenticated and associated to an access point. However, you are unable to obtain an IP address.Which of these has caused this problem?()