A.controller name
B.outdoor area
C.floor area
D.networks
E.mac address
F.ip address
您可能感興趣的試卷
你可能感興趣的試題
A.router (config)# wlccp authentication-server infrastructure eap group_1
B.router (config)# wlccp authentication-server infrastructure eap-fast group_1
C.router (config)# wlccp authentication-server client eap-fast group_1
D.router (config)# wlccp authentication-server client eap group_1
A.registration error
B.authentication failures threshold
C.http disabled
D.telnet disabled
A.administrators
B.system monitoring
C.network operator
D.power users
E.admin
F.users’ assistant
When configuring vlans on an autonomous access point.
What must be configured on the connected switchport?()
A.802.1q trunking
B.vtp trunking
C.isl trunking
D.dpt trunking
There are 30 managed access points on the wlse. a radio scan is started but fails. Upon
inspection of the device list in the reports tab, you notice a red indicator on the wds access point. upon inspection of the wds access point through its guid, it is discovered that the security keys are not set up between the wds access point and the wlse.
Which of the following is mis configured?()
A.snmp communities
B.telnet/ssh user/password
C.wlccp credentials
D.http user/password
You are using adu and are authenticated and associated to an access point. you are unable to obtain an ip address.
Which of the following will cause this problem?()
A.aes encryption enabled
B.tkip enabled
C.third-party wireless supplicant enabled
D.802.1x authentication type enabled
On a series 1010 lightweight access point, the alarm led is flashing red, and all other leds are off.
What is the lightweight access point indicating?()
A.it has lost contact with controller.
B.its ip address already exists.
C.it requires a code upgrade.
D.it is operating normally.
A.router# show wlccp ap
B.router# show wlccp wds ap
C.router# show wlccp cckm
D.router# show wlccp wds cckm
A.dictionary
B.bit-flip and replay
C.mac spoofing
D.man-in-the-middle
A.https
B.tftp
C.rmi
D.http
E.ftp
最新試題
You are configuring a wireless LAN controller for QoS.Which 802.11e user priority tag should you apply to voice applications?()
Which protocol does the RADIUS server use inside the secure tunnel of EAP-FAST to authenticatethe client when one-time passwords are in use?()
A Cisco Wireless Location Appliance has been added to track RFID tags placed on laptops beingused in a school.Classrooms at the school have concrete block walls. During testing,you discoverthat the accuracy of the system needs to be improved.You decide to edit the map in the Cisco WCS to add the interior walls.How many interior walls can you add to improve the accuracy of thelocation appliance?()
Which of the following accurately represents the functionality of a lightweight access point configured to operate in sniffer AP mode?()
A mobility group is created by a Cisco WLCM and 4402 Series Wireless LAN Controller. A client thatis anchored on the Cisco WLCM roams to an access point on the 4402 controller. You then run adebug command on the 4402 controller.Which message would best describe the establishment ofthe tunnel from the foreign controller’s perspective?()
You are installing a Cisco Aironet 1000 Series controller-based access point. When you boot it, allthe LEDs on the access point blink together.What does this indicate about the access point?()
Which of the following parameter sets must be configured on the Cisco Wireless Location Appliance?()
You are installing a Cisco 4402 Series Wireless LAN Controller.What type of interface is used on the uplink port?()
You are charges with implementing a secure wireless installation which will provide Internet accessto client devices but will not allow communications between wireless clients.In addition to implementing PSPF or peer-to-peer blocking on the wireless side,which of the following actionsshould you perform on the wired infrastructure?()
A Cisco WCS version 4.0 has been installed on a server with a dual Pentium 3.0 GHz processor,4GB RAM, and an 80 GB hard drive. A location appliance has been incorporated into the networkand is being monitored by the Cisco WCS. There are 3000 devices to be tracked but not all of themare being tracked on the Cisco WCS.What can be done to correct the problem?()