A.128
B.32
C.16
D.64
您可能感興趣的試卷
你可能感興趣的試題
A.50
B.128
C.512
D.1024
You are using adu and are authenticated and associated to an access point. however, you are unable to obtain an ip address.
Which of these has caused this problem?()
A.invalid ssid
B.invalid wep key
C.invalid encryption type
D.invalid 802.1x authentication type
A.network connections
B.location views
C.access points
D.object definitions
Yours truly, have been called upon to add location-based services into an existing controller-based wireless design which primarily encompasses handheld devices such as barcode scannersand cisco 7920 wireless ip phones.
In which mode should you deploy the additional access points to achieve the density required without excessive co-channel interference?()
A.tracking mode
B.monitor mode
C.location mode
D.sniffer mode
A cisco aironet 1020 controller-based access point has been connected to a catalyst 3550-24 pwr switch. however, when it is powered up, the access point fails.
What has caused this problem?()
A.access point does not support 802.11h
B.incorrect switch power supply
C.switch port is not enabled
D.switch does not support 802.3af
E.access point has not been initialized with the primary controller
A.acceptance test plan
B.change management
C.incident management
D.configuration management
A.ongoing support handoff meeting
B.staff training
C.detailed design development
D.staging and system migration
On a standalone access point, client association using eap-cisco wireless (cisco-leap) is failing, but association using eap-peap is functioning.
What needs to be enabled on the standalone access point to correct this issue?()
A.network eap
B.open authentication plus mac
C.open authentication plus eap
D.a shared key
You have just finished aligning a cisco aironet 1400 series wireless bridge link using
installation mode. when you set the link back to operational mode you loose association to the root bridge.
Which action will correct the problem?()
A.configure the bridge to force infrastructure devices to associate only to the ssid parameter.
B.enable passwords on both bridges.
C.configure the distance parameter value.
D.configure the proper channel.
最新試題
Which of the following accurately represents the functionality of a lightweight access point configured to operate in sniffer AP mode?()
When configuring a WLAN controller for a voice application using Cisco 7920 wireless IP phones,which two general control settings should you select?()
You are troubleshooting a problem with a Cisco 7920 wireless IP phone on a standalone WLAN.The phone rings but, when you answer, the call is dropped.What may cause this problem?()
You are installing a Cisco Aironet 1000 Series controller-based access point. When you boot it, allthe LEDs on the access point blink together.What does this indicate about the access point?()
Which of the following parameter sets must be configured on the Cisco Wireless Location Appliance?()
A Cisco Wireless Location Appliance has been added to track RFID tags placed on laptops beingused in a school.Classrooms at the school have concrete block walls. During testing,you discoverthat the accuracy of the system needs to be improved.You decide to edit the map in the Cisco WCS to add the interior walls.How many interior walls can you add to improve the accuracy of thelocation appliance?()
You are trying to change the polling parameters used by the location manager via the Cisco WCS,and your request is being denied. What is wrong?()
A mobility group is created by a Cisco WLCM and 4402 Series Wireless LAN Controller. A client thatis anchored on the Cisco WLCM roams to an access point on the 4402 controller. You then run adebug command on the 4402 controller.Which message would best describe the establishment ofthe tunnel from the foreign controller’s perspective?()
What is the maximum number of wireless controllers that the highest-end Cisco WCS server canmanage?()
You review the Failed Attempts logs on an AAA server and find: "unknown network access servererror." Which failure could produce this error?()