A.50
B.128
C.512
D.1024
您可能感興趣的試卷
你可能感興趣的試題
You are using adu and are authenticated and associated to an access point. however， you are unable to obtain an ip address.
Which of these has caused this problem？（）
A.invalid ssid
B.invalid wep key
C.invalid encryption type
D.invalid 802.1x authentication type
A.network connections
B.location views
C.access points
D.object definitions
Yours truly， have been called upon to add location-based services into an existing controller-based wireless design which primarily encompasses handheld devices such as barcode scannersand cisco 7920 wireless ip phones.
In which mode should you deploy the additional access points to achieve the density required without excessive co-channel interference？（）
A.tracking mode
B.monitor mode
C.location mode
D.sniffer mode
A cisco aironet 1020 controller-based access point has been connected to a catalyst 3550-24 pwr switch. however， when it is powered up， the access point fails.
What has caused this problem？（）
A.access point does not support 802.11h
B.incorrect switch power supply
C.switch port is not enabled
D.switch does not support 802.3af
E.access point has not been initialized with the primary controller
A.acceptance test plan
B.change management
C.incident management
D.configuration management
A.ongoing support handoff meeting
B.staff training
C.detailed design development
D.staging and system migration
On a standalone access point， client association using eap-cisco wireless （cisco-leap） is failing， but association using eap-peap is functioning.
What needs to be enabled on the standalone access point to correct this issue？（）
A.network eap
B.open authentication plus mac
C.open authentication plus eap
D.a shared key
You have just finished aligning a cisco aironet 1400 series wireless bridge link using
installation mode. when you set the link back to operational mode you loose association to the root bridge.
Which action will correct the problem？（）
A.configure the bridge to force infrastructure devices to associate only to the ssid parameter.
B.enable passwords on both bridges.
C.configure the distance parameter value.
D.configure the proper channel.
A.ssids are not case-sensitive.
B.ssids must be listed in the same order in the adu as they are in the access point.
C.a maximum of three ssids may be configured.
D.ssids may have a maximum of 16 characters.
最新試題
You want to dynamically assign users to an 802.1Q VLAN as a result of their authentication. Inorder to accomplish this.Which two IETF RADIUS attributes should you configure on the CiscoSecure ACS？ （）
Which protocol does the RADIUS server use inside the secure tunnel of EAP-FAST to authenticatethe client when one-time passwords are in use？（）
Clients using Cisco-LEAP and EAP-FAST authentication are having no problems logging on to thewireless network， but clients using PEAP are failing to log on.Which situation would result in thistype of problem？（）
On a Cisco Aironet 1240AG Series standalone access point， the radio LED is dark blue and blinking，but the status LED and Ethernet LED are both off.What does this indicate？（）
You are troubleshooting a problem with a Cisco 7920 wireless IP phone on a standalone WLAN.The phone rings but， when you answer， the call is dropped.What may cause this problem？（）
If it is properly deployed， a controller-based access point is capable of monitoring all VLANs on anetwork when you select which of the following modes from the AP Mode drop-down menu onthe controller？（）
You are installing a Cisco 4402 Series Wireless LAN Controller.What type of interface is used on the uplink port？（）
The IOS of a North American Cisco Aironet 1130AG Series standalone access point has becomecorrupt. You must therefore reload the TFTP firmware.Before you press and hold the MODEbutton， you should verify that the file name is which of the following？（）
A Cisco WCS version 4.0 has been installed on a server with a dual Pentium 3.0 GHz processor，4GB RAM， and an 80 GB hard drive. A location appliance has been incorporated into the networkand is being monitored by the Cisco WCS. There are 3000 devices to be tracked but not all of themare being tracked on the Cisco WCS.What can be done to correct the problem？（）
You review the Failed Attempts logs on an AAA server and find： "unknown network access servererror." Which failure could produce this error？（）